Resuscreed 45 is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. ADVANTAGES Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be feather edged Can act as a...
RSL Resuprime ST
Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces.
Features and Benefits:
- Versatile for many types of application
- Excellent adhesive properties
- Easy to apply
- Can be used as a tack coat for screeds
- No unpleasant or harmful odours
Resuprime ST (formerly known as Resuprime) provides excellent adhesion both as a tack coat and primer. Where surfaces are very porous, a coat of Resuprime ST may be required as a pre-primer coat before a second coat is applied as a tack coat.
For application onto new concrete, or where the RH level is likely to be above 75%, Resuprime MVT (formerly known as R.S. Dampshield FH) should be applied.
Resuprime ST is also suitable for priming self-smoothing epoxy resin finishes such as Resuflor and resin based concrete repair products such as Resupatch. Resuprime ST can also be used as a primer for high build epoxy resin coatings such as Resutop and Resucoat H.B.
- Concrete primer and sealer
- As a primer for Sherwin-Williams floor coatings and screeds – this includes RSL products.
New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding. A minimum strength of 25N/mm sq. is required.
Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water.
Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with the existing floor coating.
Resuprime ST can also be applied to existing coatings and to other cementitious screeds, which should be clean and sound with an appropriate mechanical key for adhesion.
Resuprime ST is suitable for application onto concrete and other substrates where the relative humidity is less than 75% ERH. Hygrometer readings should be done in accordance with BS 8203 to confirm the ERH of the substrate prior to application.
If the ERH is above 75%, then Resuprime MVT (formerly known as R.S. Dampshield FH) should be used in place of Resuprime ST.
The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally, to allow the ambient and substrate temperature to stabilise prior to installation.
Mixing: Pre-mix the base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used for mixing, ensure all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two to three minutes until the two components have fully combined.
The mixed unit should be applied immediately by squeegee, roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks. Coverage rates may vary depending on profile and porosity of the substrate.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Brush, Roller, Squeegee
- 5kg will cover 23m sq. @ 200 microns WFT
- Touch Dry
- 8 Hours
Be the first to ask a question about this product!
RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood. Features and Benefits:...
RSL Resuscreed PA (formerly known as Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Features and Benefits: Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation
Sikafloor 11 Pronto is a two part, medium-viscosity, fast curing primer based on reactive acrylic resins for the Sikafloor Pronto Modular System. Fast curing, medium viscosity primer to achieve a pore free cementitious substrate.
RSL Epo-Flex VJ (formerly known as Resujoint V) is a flexible, thixotropic, two-component epoxy joint sealant designed to accommodate low level movement in vertical and horizontal joints. Features and Benefits: Tough, yet flexible Adhesive Easy to clean Good chemical resistance Accommodates movement Maintains a seamless finish
This product is now only available with a minimum order of 800 litres. For an alternative, please contact our sales team on 0113 2455450 or via the contact form. Jotun Jotafloor Solvent Free Primer is a transparent two component, polyamine cured, and solvent free epoxy coating. It ensures very good adhesion on most concrete floors in...
Resupen WB is a an extremely durable polyurethane finish for concrete, plaster and wood that produces a resilient coating on Sherwin-Williams wall and flooring systems. It is available in clear, colour, matt and satin finish. ADVANTAGES Chemical resistant UV stable Good abrasion and impact resistance Hygienic and easy to clean No VOC’s...
A two-pack, water-based primer which promotes adhesion on difficult and well worn surfaces prior to applying Blackfriar Professional and other epoxy floor paints.
SikaBond Contractors PVA is a multi-purpose bonding agent, primer sealer, cement filler and plaster admixture that adheres to most common building and D.I.Y. materials except PVC and rubber. Ideal for priming unsound surfaces prior to plastering or painting, as an adhesive on wood, cork, textiles and most applications where at least one surface is porous.
Remmers Epoxy ST 100 TX is an un-pigmented thixotropic epoxy resin binder that is used as primer or as a pore filler on epoxy screeds. Thixotropic, plasticizer-free, withstands mechanical and chemical loads.
Remmers Epoxy UV 100 is a UV-protected, transparent, epoxy resin with a wide application spectrum. It is used for decorative pebble or Color Quartz covers, for fixating flake coatings and as a glossy, thick layer sealant on decorative substrates. Ideal for workshops, fabrication halls, exhibition or assembly rooms, retail and wholesale areas...
A primer exhibiting outstanding adhesion to damp concrete, the fast curing characteristics allow rapid application of subsequent MMA coatings, mortars or screeds from our range.
SCHÖNOX SHP is a solvent free, 1-component special acrylate dispersion primer for interior applications. SCHÖNOX SHP is a special primer for sound, smooth and non-absorbent substrates. Especially suitable for laying on old vinyl, linoleum and rubber coverings. With short waiting times and easy roller application, this product provides optimum adhesion.
Nu-Base Epoxy Floor Primer has been specifically-formulated to cure in damp conditions, making it an ideal choice to prime structures such as subways and multi-storey car parks, where moisture can linger. Upon proper application, this primer will act as a damp-proof membrane on the floor. Advantages Cures in damp conditions 3-5m²/KG coverage "Straw"...
This product is now only available with a minimum order of 800 litres. For an alternative, please contact our sales team on 0113 2455450 or via the contact form. Jotun Jotafloor Sealer is a sealer/primer for all Jotafloor products. Specially designed for use independently as a dust binder for concrete floors. Recommended for warehouses,...
SikaBond Rapid DPM is a solvent free reaction curing resin primer and damp proof membrane for cement based substrates. Used for priming, consolidating and sealing of absorbent and non-absorbent sub-floors, consolidating weak cement screed and isolation of old adhesive residues. Compatible with all SikaBond wood floor adhesives.
Remmers PUR Aqua Top M is used as a matt finish coating on synthetic resin coating systems. This coating is especially suitable as a finish coat in schools, hospitals, car parks and various decorative applications. Flexible, UV resistant, low dirt adhesion, easy to clean, outstanding wear resistance.