Britannia Block Paving Sealer
  • Britannia Block Paving Sealer

Britannia Block Paving Sealer


Britannia Block Paving Sealer is specifically-formulated to protect driveways, paths and flagstones, and to beautify their appearance. An ideal choice for private dwellings with large but neglected paved driveways.


  • Long-lasting.
  • Use on paving stones and flagstones.
  • Clear matt finish.
VAT excluded

£126.36 Tax incl.


This excellent paving sealer from Britannia is specifically-formulated to protect driveways, paths and flagstones, and to beautify their appearance. Driveways, paths, flagstones, paved parking areas - Just a few great uses for the Britannia Block Paving Sealer. Protects paved and concrete surfaces and breathes rejuvenated life back into them.

Features & Benefits

  • For use on paving stone and cement-based flagstones.
  • Long-lasting.
  • Solvent based Acrylic.
  • Clear matt finish.
  • Up to 2 years shelf life.

Is is advisable to use Britannia Fungicidal Wash Solution every 6-12 months to control the growth of fungus and algae on the surface.


Surfaces should be clean, dry and free from oil, grease, dust, laitence and any other deleterious materials. Ensure the paving surfaces to be treated are clean and free from any mould or fungal growth. If oil stains are present, remove with detergent and hot water. Ensure cement composite pavers are thoroughly degreased and free from release agents which will affect penetration. If mould and fungal growth are present, clean surfaces with Britannia Fungical Wash as directed. All artificial stone (cement based) and all block pavers must be left for three months minimum after placing before over coating with this product. This will allow salts to leach out which otherwise may cause unsightly white patches appearing beneath the sealer, especially when the patio is wet.


Use as supplied without thinning down.

Do not apply in temperatures below 5°C or above 25°C and should not be subjected to extremes of temperature until completely dry. The surface should be sectioned off to assist accurate coverage.

Apply THIN uniform coats maintaining a wet edge but do not allow to puddle.

It is important to undertake a representative test area to ensure that the product is suitable for your requirements prior to commencement of the project and assessed for final appearance, chemical resistance and wet & dry slip resistance. This is particularly important where the surface has previously been sealed.

Application should ideally be by an airless sprayer designed for solvent based products but application by brush or roller is also suitable.

During application care should be taken to protect adjacent areas and equipment from overspray.

Under normal conditions it will be touch dry within 1-2 hours and may be lightly trafficked in 24 hours.

All equipment should be cleaned using Britannia Special Solvent (Not White Spirit), xylene, or similar. Flush sprayers thoroughly.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details

Data sheet

Brush, Roller, Spray
Surface dry in 1-2 hours. Re-coatable overnight.

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Be the first to ask a question about this product!

Question about the product

* Required fields
16 other products in the same category:

Sikafloor 01 Primer

Sikafloor 01 Primer is a very low emission, universal dispersion primer prior to applying leveling compounds. Suitable for pre-treating on walls and floors following the recommended dilution rates.  Features & Benefits For interior use On walls and floors Solvent-free according to TRGS 610 Low consumption / high coverage Suitable...

Price £70.32
In stock

Hydron Nu-Base WB Clear Sealer

Forms the perfect seal on industrial floors and floors which require the reduction of fungal and bacterial growth, such as in hospitals. Advantages Epoxy resin Good resistance to chemicals FeRFA Class Type 1 Reduces fungal and bacterial growth

Price £87.94
In stock

Smartkote Protectakote Clear Primer Treatment

Smartkote Protectakote Clear Primer Treatment is a single component primer treatment, which can be used to prepare inorganic surfaces for the subsequent adhesion of Smartkote polyurethane coatings. This product ensures excellent adhesion of reactive, solvent-borne urethanes to unreactive inorganic surfaces without changing their appearance....

Price £10.20
In stock

405 Tack Primer

Developed for use prior to the application of various epoxy mortars and screeds in our range to promote adhesion.

Price £22.33
In stock

401 WG Epoxy Floor Primer

401 WG Epoxy Floor Primer is a fast curing version of 401 Epoxy Floor Primer designed to be used in lower temperatures or when a fast return to service is required. 401 WG Epoxy Floor Primer is a clear primer, especially formulated to provide excellent adhesion to a variety of surfaces prior to the application of our coatings or as a clear sealer in its...

Price £82.93
In stock

RSL Resutop Clear

Resutop Clear is a two-pack, high solids, high-build epoxy coating for application as a chemical resistant heavy duty floor coating, used as a clear sealer for decorative flooring systems such as Decora MS, producing a seamless, hard wearing, hygienic floor finish. Low odour Good colour stability Excellent slip resistance with the use of...

Price £67.88
In stock

Sika Block Paving Seal

Sika Block Paving Seal is a low odour clear resin which impregnates and seals block paving, resisting oil and diesel spillage whilst improving the overall appearance of the paving blocks with a matt finish. Ideal for vehicle and pedestrian areas, new and existing drives, forecourts, parking areas, walkways and paths, etc.  Features &...

Price £47.91
In stock

Sika Bonding Primer

Sika Bonding Primer is a rapid curing, water based, two-component primer to consolidate substrates and enhance the adhesion of SikaRoof MTC, Sikalastic, Sikafloor and Sikagard products. Features and Benefits: Rapid curing, overcoat possible after 1 hour Long pot life - up to 12 hours Low odour, water based product Consolidates dusty or...

Price £56.07
In stock

Remmers PUR Aqua Top 500 2K M

Remmers PUR Aqua Top 500 2K M is a water based, silk matt, transparent, 2-component sealant with very good resistance to UV and chemicals, extremely little tendency to soil and little susceptibility to scratches. Silk matt finish Slip-resistant Lightfast Water vapour diffusion capable Transparent sealant For all Remmers Epoxy and PUR...

Price £243.16
In stock

RSL Resucoat GC

RSL Resucoat GC (formerly known as R.S Screed Seal) is a two-pack epoxy resin surface coating for use with other RSL and Sherwin-Williams products, filling any voids, pockets or interstices exposed in the surface.  Features and Benefits:  Enhances chemical resistance Prevents water spillage Improves cleanability Hygienic No shrinkage...

Price £82.00
In stock

707 MMA Metal Primer

707 MMA Metal Primer exhibits outstanding adhesion for steel, galvanised steel, aluminium, and unglazed ceramic tiles and is to be used prior to any of the MMA range of coatings, mortars, and screeds. Features and Benefits:  Rapid cure, even at low temperatures Very good corrosion resistance Excellent adhesion Impervious to water...

Price £85.05
In stock

Sika Primer MB

Sika Primer MB is a primer and moisture control coating for cementitious substrates prior to levelling or bonding with elastic sikabond adhesives. It is a one coat, 2-part, solvent free, low viscosity, epoxy resin primer for use in conjunction with Sika Schönox levelling compounds, dispersion primers and SikaBond Wood Floor adhesives....

Price £84.75
In stock

305 HD Clear Sealer

Provides a clear, glossy, tack free surface, even in cool, damp conditions. Cures rapidly and is a versatile, chemical resistant sealer/clear coating for concrete and our range of epoxy screeds and mortars.

Price £85.05
In stock

Everbuild 908 DPM

A ready to use, odourless, rubber enriched bitumen emulsion providing a highly effective damp-proof membrane

Price £52.46
In stock

SikaTop 50

SikaTop 50 is a water based primer used as part of the Sika EmotionFloor range for high absorbent substrates. Excellent adhesion on absorbent substrates, prevents loss of water into the substrate, economic, increases durability, resistant to alkaline pH, ready to use, easy to use, for substrates with higher moisture content. Particularly for...

Price £33.60
In stock

SikaBond Waterproof PVA

SikaBond Waterproof PVA is a waterproof vinyl acetate polymer especially formulated for exterior use as an adhesive and sealer. Features and Benefits Waterproof formula Internal/external use Primer, sealer and cement admixture Suitable for brickwork, mortar, render, screed and plaster Easy to use and unlike normal PVA it will not...

Price £51.77
In stock