Coo-Var Dampshield is a gas permeable epoxy resin membrane tolerant of residual moisture in concrete floor, enabling earlier covering.
- Enables resin finishes sooner
- Easy application
- Can be applied to substrates with hygrometer readings up to 97% RH
- Solvent free
- Low odour
Coo-Var Dampshield is a two-component epoxy resin membrane that is tolerant of residual moisture in concrete floors. This enables earlier access onto the floor than would otherwise be available for the application of screeds, coatings and other floor coverings including carpets, tiles, vinyl and wood.
- Concrete floors
- Concrete screeds no less than 50mm thick
- Well bonded underlayments
The surface must be of sufficient quality, continuity and mechanical strength to ensure even coating. Underlayments must be stable to the effects of water. If not the concrete floor must contain an integral damp-proof membrane to prevent further ingress of water from the ground. Where laid onto a concrete surface where there is no DPM or where damage may have rendered the DPM ineffective, due consideration must be given to the possible presence of hydrostatic pressure, and the consequences of creating a barrier layer resulting in the pressure /water flow being directed elsewhere.
Apply by Brush, roller or trowel.
Brush wash: Thinners 16 (Do not thin).
Recommended Dried Film Thickness Per Coat: 230 microns
Recommended Wet Film Thickness Per Coat: 230 microns
Works particularly well as a system underneath Coo-Var Profloor Plus.
30 minutes at 20°C
Estimated coverage: 20m2 per mixed unit.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Typical Coverage (per coat)
- 4m² per KG
- Touch Dry
- 24 Hours
Be the first to ask a question about this product!
Rust-Oleum 5401 Epoxy Impregnation Primer is solvent free and improves adhesion on concrete and other porous, mineral surfaces: Primarily intended for roller and brush application Provides a good key for adhesion on porous, mineral substrates Impregnation of porous and brittle floors Can be applied on slightly damp surfaces Also ideal...
Rust-Oleum 7201 Universal Floor Primer is ready for use solvent based adhesion primer based on a special epoxyester binder. Improves the adhesion of floor paints on mineral substrates. 1 component, easy to apply it can be recoated with all Rust-Oleum or Mathys floor paints.
Sikafloor 327 is a 2-part, tough, elastic polyurethane self-smoothing resin coating for indoor use in Decorative and Industrial flooring. Sikafloor 327 is solvent free, very low VOC emission and part of the Sika Comfort Floor Tough system.
Sikafloor ProSeal 90 is a curing and sealing compound for concrete floors. It is a one component Sikafloor product that has higher efficiency curing, sealing and hardening liquid and is suitable for exterior and interior application.
Remmers PUR Aqua Top M is used as a matt finish coating on synthetic resin coating systems. This coating is especially suitable as a finish coat in schools, hospitals, car parks and various decorative applications. Flexible, UV resistant, low dirt adhesion, easy to clean, outstanding wear resistance.
Bradite Floor Primer is a clear coating solution to prime power floated, non-porous concrete and quarry tiles ready for top coating. Excellent for food areas due to it's low-odour and non-taint solution. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004. Advantages Primer and topcoat can be applied the same day...
Resugrip is a high-build, pigment and solvent-free polyurethane floor binder for when anti-slip is essential. It is designed to be added to surface dressing with aggregates and is very hard-wearing. ADVANTAGES Good chemical resistance High bond strength Will cure at temperatures down to 5°C Coloured aggregates are available to make it decorative...
Remmers Epoxy FAS 100 is a substrate tolerant, unpigmented epoxy resin binder that is used as an impregnation agent, primer, levelling layer and for the production of compression resistant mortars, flow mortars, blinding layers for blinded covers.
Remmers PUR Aqua Top 2K SG Plus is a silk gloss, water based, textured, transparent sealant with class R 11 slip resistance used as a slip resistant sealant for all Remmers Epoxy and PUR Coatings as well as for fixating and sealing Remmers Flake Coatings. The water based, 2-component sealant has good resistance to UV-light and chemicals....
Rust-Oleum Powerfloat Epoxy Floor Primer Rapid 3366 is a rapid curing 2-component solvent-free epoxy primer designed to improve the adhesion of coatings to difficult substrates such as power-floated concrete.
401 WG Epoxy Floor Primer is a fast curing version of 401 Epoxy Floor Primer designed to be used in lower temperatures or when a fast return to service is required. 401 WG Epoxy Floor Primer is a clear primer, especially formulated to provide excellent adhesion to a variety of surfaces prior to the application of our coatings or as a clear sealer in its...
SCHÖNOX VD universal acrylic primer is for use prior to apply SCHÖNOX underlayments on porous and non porous substrates in interior areas. Suitable for pre-treating on walls and floors following the recommended dillution rates.
Remmers Epoxy UV 100 is a UV-protected, transparent, epoxy resin with a wide application spectrum. It is used for decorative pebble or Color Quartz covers, for fixating flake coatings and as a glossy, thick layer sealant on decorative substrates. Ideal for workshops, fabrication halls, exhibition or assembly rooms, retail and wholesale areas...