Rust-Oleum 5401 Epoxy Impregnation Primer

Manufacturer:

Rust-Oleum 5401 Epoxy Impregnation Primer is solvent free and improves adhesion on concrete and other porous, mineral surfaces:

  • Primarily intended for roller and brush application
  • Provides a good key for adhesion on porous, mineral substrates
  • Impregnation of porous and brittle floors
  • Can be applied on slightly damp surfaces
  • Also ideal as primer for concrete repair products
Bulk Buy

£24.77 tax excl.

£29.72   tax incl.

Product Description

Rust-Oleum 5401 Epoxy Impregnation Primer is solvent free and improves adhesion on concrete and other porous, mineral surfaces. Designed for application on concrete and masonry Rust-Oleum 5401 Epoxy Impregnation Primer is primarily intended for roller and brush application. It provides a good key for adhesion on porous, mineral substrates prior to the application of several Rust-Oleum systems like; 9100, 9200, 9600, 5500, Pegakote9400 and can also be used as a tack-coat for Rust-Oleum 5180 Epoxy Repair Mortar.

Features & Benefits

  • Impregnation of porous and brittle floors
  • Contains no solvents
  • Can be applied on slightly damp surfaces
  • Also ideal as primer for concrete repair products

NEW: Now also available in convenient 1 litre packaging, ideal for smaller projects the new convenient 2-component packaging provides the base and activator in one convenient kit and the activator is supplied with a user-friendly spout cap.

TECHNICAL DATA

 Density: 1.07 kg/l
 Gloss Level: Gloss
 Solids Content in Volume: 100%
 Solids Content in [email protected] 100%
 Heat Resistance: 100°C (dry heat) - 50°C (wet heat)
 Compressive Strength: 50 MN/m²
 Tensile Strength: 10 MN/m²
 Flexural Strength: 70 MN/m²
 Mixing Ratio: Activator = 3 : 2 (Volume)

DRYING TIMES AT 20°C/RH 50%

 Touch Dry: 16 h (20°C), 36 h (10°C), 12 h (30°C)
 Dry to handle: 16 h (20°C), 36 h (10°C), 12 h (30°C)
 Dry to Recoat: 16 h (20°C), 36 h (10°C), 12 h (30°C)
 Fully Cured: 7 d (20°C), 14 d (10°C), 5 d (30°C)
 Pot Life: 30 min
 Induction Timer: 10 min

SURFACE PREPARATION

New concrete should cure and dry for at least 30 days prior to the application of the product. Remove oil, grease and all other surface contaminations by alkaline or high pressure (steam) cleaning in combination with appropriate detergents. Remove all laitance, loose or unsound concrete by vacuum-blasting or etching with Rust-Oleum Mathys 108 Surfa Etch Solution. Remove concrete curing compounds completely. Large surfaces should preferably be prepared by abrasive blasting (vacuum blasting) or flame cleaning. Profile maximum 0.5mm. Defects in the concrete should be repaired with Rust-Oleum 5180 Epoxy Repair Mortar. Small (hair) cracks and air-pockets should be repaired with Rust-Oleum 5412 Epoxy Filler. The surface should be clean and dry during application.

DIRECTIONS FOR USE

Stir individual components thoroughly before mixing them together. Use a low speed mixer in combination with the boxing method.

APPLICATION CONDITIONS

Temperature of air and substrate between 10 and 35°C and relative humidity below 85%. The substrate temperature must be at least 3°C above dew point.

APPLICATION & THINNING: BRUSH

Use natural bristles, longhair brushes.

Thinning: Absorbent mineral substrates like concrete:

APPLICATION & THINNING: ROLLER

Use medium nap, 12 mm, perlon or polyester rollers. For textured surfaces use long nap 14-18mm rollers.

Thinning: Absorbent mineral substrates like concrete:

CLEANING OF EQUIPMENT / SPILLS

Use Rust-Oleum Thinner 160.

REMARKS

  • Food should be stored separately or covered adequately during application of the Rust-Oleum 5401 Epoxy Impregnation Primer.
  • The compression strength of the concrete should be minimum 25 N/mm², the tensile strength minimum 1.5 N/mm².

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Technical Data

Typical Coverage (per coat)10m² per litre
Touch Dry16 Hours
ApplicationBrush, Roller
The figures stated above are approximate. Please ensure you refer to all datasheets for full application information.

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions



Be the first to ask a question about this product!

Question about the product

* Required fields
Send

The question has been correctly sent

Free delivery

On orders over
£75.00 + VAT

Low trade prices

Our best trade prices on everything!

Technical Advice

Fast FREE Technical Advice for Products & Projects

Click & collect

Order and collect from
our Leeds based trade store.
silent-exothermic unable