RSL FasTop Multi SL45

SL45B
RSL2975

FasTop Multi SL45 (formerly known as Resuthane SL45) is a water-based polyurethane resin floor screed designed to leave a smooth, seamless non-slip matt surface for your industrial environment.

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
Size
Finish
£60.71(ex. VAT)
£72.85 (inc. VAT)
Quantity
Product not available
Temporarily Out of Stock

Description

FasTop Multi SL45 (formerly known as Resuthane SL45) is ideal for environments that are hard wearing, but require a smooth and continuous floor system. It can be used on small and large areas alike, is non-dusting and non-taint. It is highly hygienic and does not gather bacteria.

Individual components (base, hardener, aggregate, colour pack) available to purchase seperately

Recommended Uses

  • Commercial kitchens
  • Dairies
  • Breweries
  • Food processing plants
  • Abattoirs
  • Medical environments
  • Veterinary surgeries

Preparation

New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding. A minimum strength of 25N/mm sq. is required.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

To ensure the maximum bond is achieved, grooves must be cut into the perimeter of the subfloor, typically 5mm deep by 10mm wide. These should be inset approximately 150mm from, and running parallel with the walls and adjacent to any doorways, plinths etc. Including any finished edge i.e. both sides of a day work joint. The groove must have a neat square edge and the FasTop Multi SL45 laid to the full depth forming a perimeter anchorage.

Priming

Open and porous substrates will require priming with Resuprime ST on dry substrates only with less than 75% ERH reading. Where the relative humidity of a substrate exceeds 75% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:
ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat

For further information please refer to individual product data sheets.

Application

FasTop Multi SL45 may be applied to substrates with a surface temperature in the range of 5-20°C and a relative humidity <90% RH , with a minimum air temperature of 8°C and no condensation. Do not pre-warm this product as working times will be substantially reduced if materials are warm.

When the primed surface is tack free, FasTop Multi SL45 should be applied at the required rate as soon after mixing as possible. (Delay can result in variation in surface finish, colour and add to application problems).

NB: Cure times are extended at low temperatures.

Mix the coloured base component to an even consistency, ensuring the redispersion of any settled pigment. Thoroughly scrape the contents of the base and hardener components into the same container and mix thoroughly for one minute. Pour the combined base and hardener into a rotary drum mixer and add the aggregate component steadily, until a homogeneous mix of the three components is achieved.

When thoroughly mixed the compound should be poured evenly over the appropriate area to be covered (monitoring rate of coverage to ensure correct depth of screed). Low floor temperatures and reduced thickness may reduce the flow properties of these products. Work out the mix rapidly and evenly over the area with a notched trowel, pin rake or similar to the appropriate thickness. Roll immediately with a spiked roller to achieve an even smooth surface and remove entrapped air.

NB: Spiked rolling should be undertaken immediately after trowelling. Do not re-roll later.

FasTop Multi units should be applied consistently with mixes from the same batch used consecutively where adjacent areas are being laid.

Product Details
NPH

Data sheet

Manufacturer
RSL
For Use By
Industrial Use
Interior / Exterior Use
Interior
Water / Solvent Based
Water
For Use On
Concrete
Application Method
Trowel, Rake, Spiked Roller
Sheen
Matt
Colour
Standard / Ready Mixed
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Three-Pack
Product Certifications
BS EN 13892-8:2002, EN 13501-1, EN 13892-4:2002,
Pack Size
19KG
Application
Trowel, Spiked Roller.
Coverage
19kg will cover 1.9 sq. m @ 5mm
Base Type
Water-Based
Exterior / Interior Use
Interior Use
Suitable For Use On
Concrete
Components
3K
Product Type
Polyurethane Cement
Colour Family
Blue
Colour Family
Orange
Colour Family
Black
Colour Family
Beige
Colour Family
Green
Colour Family
Red
Colour Family
Yellow
Colour Family
Grey
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resuprime ST Bonding & Priming Coat

Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces.  Features and Benefits: Versatile for many types of application Excellent adhesive properties Easy to apply Can be used as a tack coat for screeds No...

Price £108.46 (ex. VAT)
In Stock and Available for Delivery

RSL Resuprime MVT

RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood.  Easy application Use on...

Price £147.10 (ex. VAT)
In Stock and Available for Delivery

RSL FasTop Multi Individual Components

RSL FasTop Multi Individual Components allows the purchase of individual parts from the FasTop Multi range of flooring products and coatings. Choose bases, hardeners and colour pack resin components from the drop down menu. Full product packs are available to purchase: RSL FasTop Multi TG69 RSL FasTop Multi RS69 RSL FasTop Multi SL23...

Price £6.14 (ex. VAT)
In Stock and Available for Delivery