Britannia Marking Paint
  • Britannia Marking Paint

Britannia Marking Paint

LMP

Britannia Marking Paint is a water-based acrylic coating for use externally on cycle lanes or pedestrian walkways. It renews and protects driveways, and can provides clear demarcation areas for indoor floors, corridors and offices.

  • Tough and long lasting
  • Slip resistant finish
  • Eco-friendly
  • Equally suitable for tarmac or concrete surfaces
  • Available in a range of colours
  • Suitable for sports surfaces

Colour
  • Current colour: Spring Green
Choose a colour
Close colour picker
  • Spring Green
  • Yellow
  • Saxe Blue
  • Forest Green
  • Dark Blue
  • Bright Red
  • Brick Red
  • Black
  • Terracotta Red
  • Summer Red
  • Light Holly
Size
£38.27
VAT excluded

£45.92 Tax incl.
Quantity

Description

Britannia Marking Paint is a single pack water-based coating used to colour external cycle ways and pedestrian refuges. It can also be used to renew and protect driveways. Equally suitable for use on tarmac or concrete surfaces.

In addition, it can be used indoors to provide clear demarcation areas for floors, corridors and offices.



Quick Links - Click To Jump To Section:




Features & Benefits


  • Safe water-based product
  • Eco-friendly
  • Tough and long lasting
  • Slip resistant finish
  • Equally suitable for tarmac or concrete surfaces
  • Single-pack product
  • Interior and exterior use
  • Can be brush, roller or spray applied
  • Not suitable for heavy traffic areas



Spreading Rate


These will vary depending on substrate, the site conditions and longevity required.

Typically spreading rates will vary depending on the end use.

  • 6-8 square metres per litre for spray application
  • Up to 12 square metres per litre for brush or roller application
  • Dependent on substrate, texture and porosity of the surface
  • Apply 2 coats



Drying Times


  • Drying is approximately 2-4 hours dependent on ambient temperature
  • Avoid painting when rain is expected or under poor drying conditions – below 5°C
  • Curing of the coating can be extended at lower temperatures, dependent on coating thickness, substrate and texture



Preparation


  • All surfaces should be dry (not damp)
  • Free from loose or flaking material, dirt grease and vegetative growth
  • Vacuum or pressure blasting with air or water may remove any debris
  • Brushing (manual or machine) may be suitable
  • If in doubt always test a small area prior to use
  • Not to be applied if there is salt contamination or frost



Application


  • Stir well before use as stainers used can separate with time, best to mix thoroughly when using different batches
  • Surfaces that are cold – below 5°C – are not suitable for coating
  • Hot surfaces – above 30°C – should be cooled with water spray before application otherwise paint will dry before film formation is completed
  • Please follow the coverage rates shown in Spreading Rate Section
  • Apply an even coat either by brush, roller or by airless spray
  • Tip size of 28 Thou is recommended for airless spray
  • A new macadam surface should be left to oxidise for at least four weeks (longer in winter than in summer) before painting
  • Priming is not normally required, however the first coat on concrete or porous surfaces, should first be thinned up to 10% with water and allow to dry
  • Apply during April to October (exterior)

Initial Use After Application:

  • Britannia Marking Paint should be applied during the summer months, when surfaces should be left to dry for approximately 2-4 hours before they are re-opened for use
  • At the beginning and towards the end of summer, when temperatures are cooler and drying can take longer, it is advisable to extend this period by 1-2 hours or even overnight depending on the prevailing weather

Maintenance Of Surface:

  • Do not apply salt or de-icer when surface is frozen



Cleaning


  • Clean all equipment with water immediately after use



Shelf Life & Storage


  • Up to 12 months if stored correctly in an unopened container
  • Store above 5°C



Precautions


  • Keep out of reach of children
  • In case of contact with eyes wash immediately with plenty of water
  • Remove splashes from skin with soap and water or a recognised hand cleaner
  • Protect from freezing
  • Do not apply paint if there is a risk of heavy rain or frost
  • Do not use near fishponds



Product Details
LMP

Data sheet

Interior / Exterior Use
Interior and Exterior
Water / Solvent Based
Water
For Use On
Tarmac, Concrete
Application Method
Brush, Roller, Spray
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Pack Size
5L, 20L
Application
Brush, Roller, Spray
Coverage
6-8 square metres per litre for spray application. Up to 12 square metres per litre for brush or roller application. Dependent on substrate, texture and porosity of the surface. Apply 2 coats.
Touch Dry
Approximately 2-4 hours.
UN Number
N/A
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send