Bradite Rapid


Bradite Rapid is a high performance single-pack moisture cure polyurethane floor coating that is ideal for commercial and industrial environments. Available in a large amount of colours, including RAL shades, the tough and flexible film will provide water and chemical resistance. 


  • Available in more than 350 colours in RAL & BS
  • Ideal for use as a floor sealer
  • Hard-wearing
  • Produces a tough flexible film
  • Also available as a clear coating

Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

**Available for delivery - see Delivery Options below**

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
VAT excluded

£114.47 Tax incl.


Bradite Rapid is a quick-drying floor paint that is hard-wearing enough for forklift traffic. It gives good chemical and water resistance and is ideal for industrial and commercial environments.

Can be used with Bradite Low Slip Additives SA12 or SA14 to provide additional under foot traction.

Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems. 2004/42/EC EU limit value for this product (cat.A/I sb): 500g/l (2010). This product contains max.300g/l VOC.

Features & Benefits

  • Available in more than 350 colours in RAL & BS
  • Produces a tough flexible film.
  • Hard-wearing.
  • Dries quick.
  • Ideal for use as a floor sealer.
  • Suitable for forklift traffic (after 48hrs).


For internal steel, wood, concrete and other absorbent mineral substrates which are free of contamination, dust, efflorescence and have been properly prepared and primed. Compatibility with existing coatings should be confirmed by preparing and painting a test patch. Not suitable for applying over asphalt, bitumen, epoxy tar, alkyd, chlorinated rubber or vinyl based paints.

Substrates should be dust free and completely dry before coating. When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance. Power floated, shiny or unpainted non porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite TA37, or primed using Bradite Floor Primer ES40. Please consult the product data sheet for more details.

High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate. Bradite TD39 industrial strength detergent should be used if necessary to remove all grease and oil.

Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting. Substrate should be dust free and completely dry before coating.


Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.

Brush and Roller: Supplied ready for use. Thin, if required, with 0-5% Bradite thinner TP33.

Conventional Air Spraying / Airless Spraying: Not recommended.

Clean all equipment immediately after use with Bradite Thinner TP33 for best results.

For application on concrete, wood or other absorbent substrates, the first coat should be thinned 10-20% with Bradite Thinner TP33 to allow penetration into the substrate.

1st coat: Bradite Rapid Floor Paint PW74 (thinned).

2nd coat: Bradite Rapid Floor Paint PW74.

3rd coat: Bradite Rapid Floor Paint PW74.

For maintenance painting, the 1st coat will be a touch up to bare areas only. While the floor will take light foot traffic after overnight drying, full cure may take 4 days at 20⁰C, and should not be subject to heavy traffic for at least 48 hours. Please note that drying/curing times will vary depending on film thickness, temperature and relative humidity. Due to the rapid drying of Bradite Rapid PW74 it is advised that once opened the can should not be resealed.

Bradite Rapid Floor Paint PW74 is suitable for use with Bradite Low Slip Additives SA14 or SA12, which can be either incorporated into the paint or hand broadcast into the applied wet paint. Please see data sheet for more information about this.

Please note this product is for interior use only - Not UV stable.

Product Details

Data sheet

Interior / Exterior Use
For Use On
Steel, Wood, Concrete
Application Method
Brush, Roller, Spray
Fully Tintable
Single, Two or Three Pack
Pack Size
Brush, Roller
10m2 per Litre
Touch Dry
2 Hours
UN Number

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Be the first to ask a question about this product!

Question about the product

* Required fields