HMG Polyurethane Floor Paint

TOPFLOOR

HMG Polyurethane Floor Paint is designed to provide a hard wearing yet economical surface coating. Its durability is achieved by the use of excellent quality resins, which also provide the user with a product that is very easy to use.

  • Ease of use
  • Available in a wide colour range including RAL & BS shades

Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

**Available for delivery - see Delivery Options below**

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
Size
Finish
£38.17
VAT excluded

£45.80 Tax incl.
Quantity

Description

HMG Polyurethane Floor Paint is designed to provide a hard wearing yet economical surface coating. Its durability is achieved by the use of excellent quality resins, which also provide the user with a product that is very easy to use.



Click To Jump To Section:




Features & Benefits


  • Ease of use
  • Available in a wide colour range including RAL & BS shades



Product Specification


Technical Data
Volume Solids: 52.5%
VOC Content: 0.450kgs/ltr
SG: -
Viscosity: 250 mPas
Density: 0.929 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Flash Point: 31°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Brush: n/a n/a
Roller: n/a n/a



Coverage: 10 square metres per litre (Theoretical)

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Touch Dry: 2 hours
Dry To Handle: 4 - 6 hours
Dry To Recoat: After 8 hours @ 20°C
Fully Cured: 24 hours



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.



Application Methods


Technical Data
Brush Roller
Mixing Ratio: Ready for use Ready for use
- -
Thinner Options: n/a n/a
- -
Viscosity: n/a n/a
Number Of Coats (Guide Only): 1 - 2 coats 1 - 2 coats
Flash Off: n/a n/a



Product Notes


Information on basic physical and chemical properties
Form: Liquid
Colour: According to product specification
Odour: Characteristic
Odour Threshold: Not determined
pH-value: Not determined
Change in Condition
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 135°C
Flash Point: 31°C
Flammability (solid, gas): Not applicable
Ignition temperature: 200°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 0.6 Vol %
Explosion limits: Upper: 7.0 Vol %
Vapour pressure at 20°C: 6.7 hPa
Density at 20°C: 0.929 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: 250 mPas
Viscosity: Kinematic: Not determined
Solvent content: Organic solvents: 28.4%
Solids content: 52.5%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.

Click to go back to the top of the page

Product Details
TOPFLOOR

Data sheet

Manufacturer
HMG Paints Limited
For Use On
Concrete
Application Method
Brush, Roller
Sheen
Matt, Satin, Gloss
Colour
Fully Tintable
Single, Two or Three Pack
Single
Pack Size
5L
Key Features
Ease of use. Available in a wide colour range including RAL & BS shades.
Touch Dry (at 20°C)
2 Hours
Dry to Handle (at 20°C)
4 - 6 Hours
Dry to Recoat (at 20°C)
After 8hrs @ 20°C
Fully Cured (at 20°C)
24 Hours
Density
0.929 g/cm³
Solids by Volume
52.5 %
VOC
0.450kgs/ltr
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers.
Finish
Matt, Satin and Gloss
Size
5Ltr
UN Number
1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Val Edwards on 2020-06-26 01:44:17
Question: 

Is this paint suitable for outdoor use please?

Answer: 

No this paint is for internal use only, for an external floor assuming the substrate is compatible, clean, dry and sound we can recommend Bradite Floor-it.

Please check the Technical Data Sheet for preparation, application details and primer requirements.

This is available in mant RAL and BS colours.


Question about the product

* Required fields
(read)
Send