Bradite Floor-It

DP9
BRA4433

Bradite Floor-It is a high-performance, ambient, crosslinking water-based acrylic floor paint for internal/external wood, steel, concrete and other absorbent mineral substrates.

  • Available in 2,500+ colours, inc. RAL Classic, BS, NCS & the new NCS 2050 colours
  • Economical, hard wearing, flexible floor coating with good chemical and excellent water resistance
  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems

Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

Coverage Calculator

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
Size
Finish
£39.47(ex. VAT)
£47.36 (inc. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

Quick Links - Click To Jump To Section:




Features & Benefits


  • High-performance ambient crosslinking water based acrylic floor paint
  • Economical, hard wearing, and flexible
  • Good chemical and excellent water resistance
  • For interior/exterior bare or previously painted suitably prepared concrete, wood, steel, tarmac or asphalt floors
  • Suitable for use in domestic and light commercial garages
  • Can be used with Bradite Low Slip Additive LS30 to provide additional under foot traction
  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems.



Preparation


  • For internal/external wood, steel, concrete and other absorbent mineral substrates which are dry, free of contamination, dust, efflorescence laitance and have been properly prepared and primed. Suitably prepared and well adhered existing coatings including, polyurethane, epoxy and chlorinated rubber. External floor surfaces should be above local water table and/or have intact DPM barrier present
  • Substrates should be dust free and completely dry before coating
  • When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance. If the concrete is loose, chipping or has concrete dust present, the coating will not perform properly unless all loose material and dust is removed and damaged areas are repaired
  • Powder Coated, shiny or unpainted non porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite Acid Etch TA37, or primed using Bradite Floor Primer ES40
  • High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate. Bradite TD39 industrial strength detergent should be used if necessary to remove all grease and oil
  • Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting



Application


  • Application and use should always conform to the codes of practice described in BS 6150 and BS 5493
  • Applicable by brush, roller, conventional air spray, or airless spraying:
    • Brush and Roller - Supplied ready for use. Thin, if required, with up to 5% water.
    • Conventional Air Spraying - Thin with 5-15% Water as required, tip size - 2.0mm, tip pressure 60psi (0.4MPa)
      approximately.
    • Airless Spraying - Thin with 0 – 10% water as required, tip size - 18 thou (0.46mm) approximately, tip
      pressure - 2100 psi (15MPa) approximately.
  • For application on concrete, wood or other absorbent substrates, the first coat should be thinned 5-10% water to allow penetration into the substrate
  • For maintenance painting the 1st coat will be a touch up to bare areas only
  • While the floor will take light foot traffic after overnight drying, full cure may take 4 days at 20°C and should not be subject to heavy traffic for at least 48 hours
  • For additional underfoot traction, Bradite Low Slip Hard Aggregate LS30 should be added to the paint and mixed thoroughly just before use at a rate of 1 x 250ml LS30 tin (400g) per 5 litre of paint
  • Clean all equipment immediately after use with water for best result



Limitations


  • Compatibility with existing coatings should be confirmed by preparing and painting a test patch
  • Drying/curing times will vary depending on film thickness, temperature and relative humidity
  • Bradite Floor-It DP9 is suitable for use in domestic and light commercial garages. In the first seven days after application, vehicles should be left outside to allow tyres to cool down (especially after long journeys) to help prevent hot tyre pick up. Spills of petrol and diesel should be cleaned up as soon as possible to reduce the danger of slip and to prevent discolouration of the floor paint. Brake fluid is highly aggressive and will attack most floor paints on contact – use drip/capture pans when working on brake systems to prevent permanent damage to the floor paint finish
  • The end user and applicator must ensure that the finished floor is safe against slips in all likely usage conditions
  • Always refer to the Health and Safety sheet for the product before use, and observe the warning phrases on the label
Product Details
DP9

Data sheet

Manufacturer
Bradite
For Use By
General Use
Interior / Exterior Use
Interior and Exterior
Water / Solvent Based
Water
For Use On
Concrete, Wood, Steel, Tarmac, Asphalt
Application Method
Brush, Roller, Spray
Sheen
Semi-Gloss
Colour
Fully Tintable
VOC Levels
Low (50-149 g/l)
Single, Two or Three Pack
Single
Pack Size
2.5L, 5L
Parts
One
Base Type
Water-based
Interior/Exterior Use
Interior & Exterior
Minimum Applied Thickness
39 microns/coat
Suitable Substrates
Concrete, wood, steel, tarmac, asphalt
Key Features
Non-yellowing, low odour, fast drying
Application
Brush, Roller, Spray
Fully Cured (at 20°C)
4 days
Recommended Thinner/Cleaner
Water
Compatible Primers
Bradite Floor Primer ES40
Density
1.179 kg/L
Solids by Volume
38.59%
VOC
101 g/L
Shelf Life (from date of manufacture)
12 months
Touch Dry
16 hours minimum, after final coat
Touch Dry
30 Minutes
Recommended Dry Film Thickness
39 microns/coat
Recommended Wet Film Thickness
100 microns/coat
UN Number
N/A
Dry to Recoat
1 hour minimum
Fully Cured
7 days
Base Type
Water-Based
Exterior / Interior Use
Exterior & Interior Use
Suitable For Use On
Concrete
Suitable For Use On
Steel
Suitable For Use On
Wood
Components
1K
Product Type
Acrylic
Colour Family
Red
Colour Family
Pink
Colour Family
Cream
Colour Family
Purple
Colour Family
Grey
Colour Family
Black
Colour Family
Blue
Colour Family
Brown
Colour Family
Orange
Colour Family
Beige
Colour Family
Yellow
Colour Family
Green
Colour Family
White
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send

IMPORTANT SHIPPING & DELIVERY INFORMATION

Bradite Floor-It is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


COVERAGE CALCULATOR
Units
Total area²
Or enter length and width dimensions:
Length
Width

*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage

    

You might also like

Bradite Floor Primer

We no longer stock this product, but can recommend Rust-Oleum 3366 Epoxy Powerfloat Floor Primer Rapid as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our...

In stock

Bradite Acid Etch

Bradite Acid Etch is a mineral acid solution used as a pre-treatment for bare concrete surfaces, for application to bare concrete floors to remove excess lime and/or to etch a surface profile to smooth concrete. Provides improved adhesion of subsequent floor coatings Manufactured under the auspices of an ISO 9001:2008 quality & ISO...

Price £24.18 (ex. VAT)
In Stock and Available for Delivery

Bradite Industrial Degreaser

Bradite Industrial Degreaser is an aqueous alkaline low foaming detergent used for degreasing contaminated surfaces prior to painting. Ideally suited for degreasing oily or soiled surfaces and for removing road dirt Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems More...

Price £7.28 (ex. VAT)
In Stock and Available for Delivery

Bradite Low Slip Additive (LS30)

Bradite Low Slip Additive (LS30) is a hard Aluminium Oxide aggregate additive providing additional under foot traction to floor coatings, used in conjunction with Bradite floor paints requiring a hard wearing low slip additive and added to the paint and mixed thoroughly just before use. Manufactured under the auspices of an ISO 9001:2008...

Price £10.27 (ex. VAT)
In Stock and Available for Delivery