Axalta ViterFloor 276 Floor Paint is a single pack polyurethane floor coating for general purpose and light traffic areas.
Axalta ViterFloor 276 Floor Paint is an economic, easily applied floor coating for concrete and wooden floors. It has a mild solvent blend to minimise reaction with existing floor coatings and minimise the lifting of old coating edges.
For use as an easy to use maintenance paint for light duty areas in shops, warehouses and industrial plant. Brush or roller application for easy routine floor repainting.
Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation
Surface Preparation
All surfaces must be clean, dry, and free from grease, oil, laitance, dust and other contamination
Bare Concrete:
Remove dirt and contamination by detergent washing, flame cleaning or other appropriate means
For the best long term coating life, laitance should be removed by vacuum blast cleaning (recommended), power grinding or acid etching
If acid etching, more than one application may be required to produce a granular surface suitable for good adhesion
Vacuum blast cleaning should produce a surface profile appropriate to the thickness of the coating being applied
If laitance is not removed, it can detach in service along with the coating, leaving patchy areas of bare concrete
Previously Painted Floors:
Abrading (as well as thoroughly cleaning) the existing coating is always recommended to optimise adhesion
As ViterFloor 276 has a mild solvent blend, there should be minimal reaction with existing coatings such as the lifting of old coating edges
A test area is recommended to confirm compatibility and that adequate adhesion can been achieved
Wood Floors:
Punch all nail heads down below the surface
Sand the surface down to clean, smooth wood using an industrial vacuum sander, cutting-in at edges with a hand sander
To give a smooth finish it is recommended to also lightly sand and vacuum between coats
Steel Floors:
Please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information
Mixing
Must be mixed thoroughly by using a mechanical agitator before use
Agitate periodically during use to ensure product remains homogeneous
The concrete surface must be dry and at least 12 weeks old
The moisture content of the concrete should not exceed 6% when measured 25mm below the surface (with e.g. a Protimeter measuring in 25mm drilled holes filled with gel), or 14% when measured with a surface moisture gauge (such as a Protimeter WME (Wood Moisture Equivalent) gauge)
Only apply in conditions of good ventilation which must be maintained during drying and curing
Do not apply when rain, mist, sleet or snow are imminent
During application and drying time of the paint coating, the surface should be dry, the relative humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
Only apply this product when the above conditions can be maintained throughout the critical application and drying/curing process
Paint temperature should ideally be at a minimum of 15ºC
Application Methods
This product is designed for brush or roller application
Product Notes
Priming: Prime bare concrete areas by thinning the first coat of ViterFloor 276 with 10-20% of 1050 Thinner to act as a sealer
Overcoating: Overcoat either wet-on-wet, or after a minimum of 16 hours at 20ºC. After 3 days at 20ºC, light abrasion will be necessary in order to achieve optimum adhesion
Anti-Slip: Dependent on the degree of anti-slip required, aggregate can be broadcast onto the wet coating surface (of a full, unthinned coat) and allowed to dry. Surplus non-adhering particles should then be brushed off and further coats of ViterFloor 276 applied to encapsulate the particles
Some shades may contain lead-based colourants and these are labelled (L)
Health & Safety
Containers are provided with safety labels which should be observed
Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Axalta ViterFloor 276 Floor Paint is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
We no longer stock this product, but can recommend Axalta TH400 Thinner as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450...