Ennis-Flint MMAXGrip PRMX 45
Ennis-Flint MMAXGrip PRMX 45 is designed as a versatile MMA coating for application to bituminous substrates, possesses excellent abrasion-resistance and non-skid properties and was developed specifically as a heavy-duty surfacing and can be applied to asphalt substrates without a primer. The product is used as a priming surfacer, a topping layer and final course on external surfaces.
**Available for delivery - see Delivery Options below**
Ennis-Flint MMAXGRIP PRMX 45 is designed as a versatile MMA coating for application to bituminous substrates, possesses excellent abrasion-resistance and non-skid properties and was developed specifically as a heavy-duty surfacing and can be applied to asphalt substrates without a primer.
The product is used as a priming surfacer, a topping layer and final course on external surfaces that are subject to pedestrain and vehicular traffic, such as roads and plazas; furthermore, it is used for coloured road markings as well as for coating mastic flooring incorporating toppings. The surface can be of any colour and this coating can even be used to create patterns or car park markings and traffic guidance.
Features & Benefits
- Maximum abrasion resistance
- Maximum anti-skid properties
- Variable roughness (SRT> 45-65)
- Permanently weather-resistant (UV-, hydrolysis and alkali-resistant)
- Any RAL colour
- Pattern and colour design possible
- Easy and fast application
Areas of Application
- Parking areas, forecourts and outdoor plazas
- Coloured road markings
- Footpaths and cycle paths (note SRT values)
- Courtyards, schoolyards, pedestrian guidance systems
- Town and market square, restricted-zone markings
- Repair and re-profiling product for road ironwork and street furniture, including manholes, gullies, pavement failures, potholes, etc.
Included in Pack
- 15.00kg MMAXGRIP PRMX 45
IMPORTANT: Ennis-Flint MMAXGRIP PRMX Catalyst MUST be purchased separately in order to use this product. The required quantity for the application conditions such be purchased accordingly (see below).
Reaction Times and Required amounts of Catalyst
|Pot life||12 min.|
|Fully cured||2 hours|
Higher temperatures or greater proportions of catalyst will shorten reaction times, while lower temperatures and smaller proportions of catalyst will extend reaction times. The following table indicates the recommended amount of catalyst required to adjust the curing reaction to the temperature.
|Substrate temperature in°C; required amounts of catalyst in % w/w (guide)|
|MMAXGRIP PRMX Catalyst||3%||3%||2%||2%||1.5%||1.5%||1.5%||1%||1%||1%|
For mixing the product:
- Twin-paddle stirrer
For applying the product:
- Rubber squeegee (45cm-60cm) or Smoothing trowel
Surface treatment with:
- Sheepskin roller/Textured Roller
MMAXGRIP PRMX 45 can be applied in top of a hardened layer of Primer. Primer is not required on asphalt surfaces.
Ennis-Flint MMAXGRIP PRMX Primer is used as a primer on absorbent substrates, e.g. concrete. For further information, please refer to the technical information sheet.
First stir the tub contents thoroughly. Then add the catalyst while stirring at the slow-speed setting and mix for 2 minutes. Make sure that the product on the base and sides of the container is incorporated. Ideally the roller-applied coating should therefore be re-potted once before stirring again. At product temperatures < 10˚C the product should be stirred for 4 minutes, as the catalyst will take longer to dissolve.
Use a smoothing trowel or rubber squeegee to spread the material evenly and smooth it over, using the particle size as a guide to layer thickness. To achieve the desired finish, go over the area with a sheepskin or textured roller.
NOTE: Ennis-Flint MMAXGRIP PRMX 45 is subject to a 7 - 10 working day lead time. It is also available in all RAL colours, except effect colours. Please contact us for further details. Additional costs and extended lead times may be applicable.
- For Use On
- Application Method
- Roller, Squeegee, Trowel
- Standard / Ready Mixed
- VOC Levels
- Ultra-Low (5-49 g/l)
- Single, Two or Three Pack
- Pack Size
- 1.4 – 1.6 kg/m²
- Touch Dry
- 30 min
- UN Number
Be the first to ask a question about this product!