Ennis-Flint MMAXGRIP™ PRMX 65
  • Ennis-Flint MMAXGRIP™ PRMX 65

Ennis-Flint MMAXGRIP PRMX 65

PRMX65

Ennis-Flint MMAXGRIP PRMX 65 is an MMA-based coating that was developed specifically for application to public main roads and side streets as well as other traffic zones. Its special properties make it particularly suitable for surfaces where coloured road markings are required on main roads and side streets in urban areas and elsewhere.

Colour
  • Current colour: White
Choose a colour
Close colour picker
  • White
  • Black
  • RAL3020 - Traffic Red
  • RAL5015 - Sky Blue
  • RAL5017 - Traffic Blue
  • RAL6018 - Yellow Green
  • RAL6024 - Traffic Green
Size
£102.69
VAT excluded

£123.23 Tax incl.
Quantity

Description

Ennis-Flint MMAXGRIP PRMX 65 is a MMA-based coating (MMA – polymethyl methacrylate) that was developed specifically for application to public main roads and side streets as well as other traffic zones. Its special properties make MMAXGRIP PRMX 65 particularly suitable for surfaces where coloured road markings are required.

Features & Benefits

  • Superior abrasion-resistance, PSV of aggregate 70-80
  • Superior skid resistance and grip > SRT 65 (SN 640 214 FGSO)
  • Resistant to mechanical stress
  • Chloride-resistant
  • Easy and fast application
  • Fast-curing
  • Solvent-free

Areas of Application

MMAXGRIP PRMX 65 is suitable for use as coloured surface markings applied on main roads and side streets in urban areas and elsewhere (including plazas, cycle tracks, footpaths, pavements and byways).

Included in Pack

  • 15.00kg MMAXGRIP PRMX 65

IMPORTANT: Ennis-Flint MMAXGRIP PRMX Catalyst MUST be purchased separately in order to use this product. The required quantity for the application conditions such be purchased accordingly (see below).

Reaction Times and Required amounts of Catalyst

 Approx. 
 Pot life  12 min.
 Rain-proof  30 min.
 Walkable/Overlayable   45 min.
 Fully cured  2 hours

Higher temperatures or greater proportions of catalyst will shorten reaction times, while lower temperatures and smaller proportions of catalyst will extend reaction times. The following table indicates the recommended amount of catalyst required to adjust the curing reaction to the temperature.

 Substrate temperature in°C; required amounts of catalyst in % w/w (guide) 
 Temperature  -5  +3  +5  +10  +15  +20  +25  +30  +35  +40
 MMAXGRIP PRMX Catalyst   3%  3%  2%  2%  1.5%  1.5%  1.5%  1%  1%  1%

Substrate Preparation

The substrate must be suitably prepared so that it is sound, dry and free from loose or adhesion-reducing components.

Concrete

Ennis-Flint MMAXGRIP PRMX Primer is used as a primer on absorbent substrates, e.g. concrete. For further information, please refer to the technical information sheet.

Asphalt

We advise against applying the product to fresh asphalt < 90d. No primer is required if the product is applied to older asphalt > 90d.

Mixing

First stir the tub contents thoroughly. The add the catalyst while stirring at the slow-speed setting and mix for at least 2 minutes. Make sure that the product on the base and sides of the container is incorporated. Ideally MMAXGRIP PRMX 65 should be repotted once then stirred thoroughly again. At product temperatures <10 ˚C the product should be stirred for at least 4 minutes, as the catalyst will take longer to dissolve.

Application

Spread the mixed material evenly using the smoothing trowel, aluminium blade or rubber squeegee and lay off to particle size thickness. For an even surface with a good grip (SRT > 65) the area must be finished with a textured roller immediately after application.

NOTE: Ennis-Flint MMAXGRIP PRMX 65 is subject to a 7 - 10 working day lead time. It is also available in all RAL colours, except effect colours. Please contact us for further details. Additional costs and extended lead times may be applicable.

Product Details
PRMX65

Data sheet

Interior / Exterior Use
Exterior
For Use On
Concrete, Asphalt
Application Method
Squeegee, Trowel, Roller
Colour
Standard / Ready Mixed
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Two-Pack
Pack Size
15KG
Application
Roller
Coverage
2.8 - 3.5 kg/m²
Touch Dry
30 min
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send