708 MMA Tarmac / Asphalt Primer is a two-pack substrate specific primer for Tarmac and Asphalt, being used prior to any suitable Rawlins MMA product. It exhibits fast curing characteristics allowing rapid application of subsequent coatings, mortars or screeds.
Rapid cure, even at low temperatures
Very flexible
Very good chemical resistance
Excellent adhesion
Impervious to water
Pre-packed units ready for use
Easily applied
Images are for illustrative purposes only and may differ from the actual product
708 MMA Tarmac / Asphalt Primer has been developed as a substrate specific primer for Tarmac and Asphalt, being used prior to any suitable Rawlins MMA product.
The product exhibits excellent adhesion to tarmac and asphalt, and the fast curing characteristics allow rapid application of subsequent coatings, mortars or screeds.
708 MMA Tarmac - Asphalt Primer is supplied as a two-pack material, comprising pre-weighed amounts of Base and Catalyst components.
New Tarmac shall be allowed to weather for at least 1 month, or until there is no evidence of residual flux oils
Tarmac and Asphalt surfaces shall be washed with detergent and water and allowed to dry
Extremely smooth Asphalt may require some light texturing by mechanical means
Mixing
Pour the contents of the Catalyst container into the Base container and thoroughly mix, preferably by mechanical means
Application
Apply by squeegee to distribute evenly over the floor, and then use a long nap lambswool roller to achieve a nominal application rate of 0.25-0.30kg/m²
Allow to cure for a minimum of 1 hour prior to applying any other suitable Rawlins MMA product
Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C
Adequate ventilation of the storage area should be provided
Keep container tightly closed when not in use
708 MMA Tarmac - Asphalt Primer has a minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions
Coverage
A 5kg pack is sufficient to prime an area of 15-20m², Exceptionally porous surfaces may require a second coat.
Limitations
Do not apply directly to concrete surfaces
708 MMA Tarmac - Asphalt Primer will taint food during application, so that all foodstuffs in the immediate vicinity must be removed or properly covered
Health & Safety
708 MMA Tarmac - Asphalt Primer is flammable during application, so that adequate safety precautions should be observed
Avoid contact of the material with skin and eyes
Wear gloves and goggles
Wash off splashes immediately with soap and water
Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Product Details
5239-867200
Data sheet
Manufacturer
Rawlins Paints
For Use By
Professional Use
For Use On
Tarmac, Asphalt
Application Method
Squeegee, Roller
Sheen
Semi-Gloss
Single, Two or Three Pack
Two-Pack
Pack Size
5KG
Dry to Recoat (at 20°C)
60 Minutes
Fully Cured (at 20°C)
24 Hours
Pot Life (at 20°C)
10-15 Minutes
Coverage
A 5kg pack is sufficient to prime an area of 15-20m², Exceptionally porous surfaces may require a second coat.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
708 MMA Tarmac / Asphalt Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins.Low Hazard Low evaporation rate Excellent solvency powers 80% biodegradable This product is for Professional Use Only Images are for illustrative purposes only and may differ from the actual productMore...