RSL Resuthane T100

T100B

Resuthane™ T100 is a three-pack polyurethane coating, that acts as the top coat when refinishing is necessary. When used with other Resuthane screeds, it ensures uniformity in concrete areas.

ADVANTAGES

  • Brush, roller or squeegee application
  • High chemical resistance
  • Resistance to hot water & steam
  • Excellent slip resistant finish
  • Matt finish
  • Very hard wearing
Colour
  • Current colour: Black
Choose a colour
Close colour picker
  • Black
  • Salsa Red
  • Stirling Grey
  • Flint Grey
  • Buff
  • Kingfisher Blue
  • Forest Green
  • Marigold
Size
Finish
£25.26
VAT excluded

£30.31 Tax incl.
Quantity

Description

Resuthane™ T100 is the icing atop the Resuthane polyurethane cake. It can be applied to coves, screeds or concrete to ensure an impeccable finish and create a seamless impression.

Like all Resuthane products, it is incredibly hard wearing, chemical resistant and highly hygienic. It can also be used as a sealer for Resuthane™ JT40. It is ideal for the hard wearing industrial environment.

RECOMMENDED USES

  • Food manufacture & processing
  • Brewing & beverage
  • Dairies
  • Commercial Kitchens
  • Pharmaceutical & chemical plant processing
  • Abattoirs
  • Heavy duty plant & traffic areas

Preparation

New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm² is required.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. if the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

Where overcoating Resuthane™ screeds, proper surface preparation is essential to ensure maximum adhesion. For Resuthane™ JT40 the overcoat intervals should be observed and if left for longer. The surface must then be prepared and roughened prior to application of Resuthane™ T100.

Priming

Open and porous substrates will require priming with Resuprime ST on dry substrates only with less than 75% ERH reading. Where the relative humidity of a substrate exceeds 75% ERH, R.S. Dampshield or Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat

For Further information please refer to recommended individual product data sheets.

Application

Resuthane™ T100 may be applied to substrates with a surface temperature in the range of 5-20°C and a relative humidity <90% RH, with a minimum air temperature of 8°C and no condensation. Do not pre-warm this product as working times will be substantially reduced if materials are warm.

NB: Cure times are extended at low temperatures.

Mixing: Mix the coloured base component to an even consistency, ensuring the re-dispersion of any settled pigment. Add the aggregate and mix to form a smooth paste that is free from bits. Once smooth, add the hardener and mix for approximately one minute. Apply the product immediately using the desired application method.

Resuthane™ T100 has a short pot life and must be used immediately after mixing. Any delay will result in loss of working time and loss of material.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
T100B

Data sheet

Manufacturer
RSL
Interior / Exterior Use
Interior
For Use On
Concrete
Application Method
Brush, Roller, Squeegee
Sheen
Matt
Colour
Standard / Ready Mixed
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Three-Pack
Pack Size
3KG
Application
Brush, Roller
Coverage
3 kg will cover 20m squared @ 100 microns
Touch Dry
8 Hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resuthane JT40

Resuthane™ JT40 is a cove and wall polyurethane resin render designed to be used with Resuthane™ floor screeds, maintaining the high levels of resilience to chemicals and hot temperatures. It is also suitable for radius coves. ADVANTAGES Seamless finish High chemical resistance Resistant to hot water &amp; steam Matt finish Extremely...

Price £45.00
In stock

RSL Resuthane T100

Resuthane™ T100 is a three-pack polyurethane coating, that acts as the top coat when refinishing is necessary. When used with other Resuthane screeds, it ensures uniformity in concrete areas. ADVANTAGES Brush, roller or squeegee application High chemical resistance Resistance to hot water &amp; steam Excellent slip resistant finish...

Price £25.26
In stock

RSL Resuprime ST

Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces.  Features and Benefits: Versatile for many types of application Excellent adhesive properties Easy to apply Can be used as a tack coat for screeds No...

Price £68.19
In stock

RSL Resuprime MVT

RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood.  Features and Benefits:...

Price £19.80
In stock