RSL Acrydur ME05

    ME05
    RSL10154

    A solvent free, two component medium viscosity Methyl Methacrylate (MMA) resin used as a highly flexible membrane Acrydur flooring systems. As a sublayer Acrydur ME05 can be used as a coating and will reduce the risk of cracking in flooring systems installed where movement will occur within a construction.

    • Recommended for use as a flexible membrane for Acrydur flooring systems and as a coating in cold stores or outdoor
    • Easy to apply, elastomeric
    • Excellent bond to substrate, fast curing

    Colour
    Size
    £0.00(ex. VAT)
    £0.00 (inc. VAT)
    Quantity
    Please choose your colour
    This Product is Made to Order, Please Contact our Sales Team on 0113 245 5450

    Description



    Quick Links - Click To Jump To Section:




    Features & Benefits


    • Ideal for:
      • Transportation
      • Industrial and Manufacturing



    Surface Preparation


    New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm² is required.

    Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and making sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Acrydur RM.

    Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with the existing floor coating.

    Where Acrydur ME05 is applied to concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.



    Priming/Application Conditions


    Substrates should be primed prior to the application of Acrydur ME05. Acrydur PR01, PR02 & PR03 is for priming substrates prior to the application of Acrydur flooring systems. Refer to product datasheets for different substrates. Porous substrates may require double priming. The primer application should be lightly scattered with sand (approximately 0.7 – 1.2 mm in size) at an approximate rate of 0.3 kg/m2.

    Acrydur ME05 is supplied in pails or drums. Before mixing ideally precondition the Acrydur resin and the Peroxide as well as the fillers and quartz components to a temperature of approximately 15 °C to 20°C.

    The application temperature should be 0°C to 30°C throughout the application and the curing period.



    Mixing


    Prior to use, stir the Acrydur to obtain an even distribution of the paraffin contained in the product. With pourable mixes, the Peroxide is the last component to be added in the mix. For mortars, add the Peroxide prior to adding the aggregate. Pour the appropriate ratio of hardening powder into the container of resin (see table below). Mix until the Peroxide is completely dissolved.

    Hardener addition % guidance

    TemperatureHardening PowderPot Life/MinutesHardening Time
    0°C6%2080
    10°C4%1540
    20°C2%1540
    30°C1%825

    Hardening powder must not be added to the reactive resin and resin/filler mix until immediately before application. In the case of pourable mixes, the hardener should be the last component added, while for mortars or very thixotropic resins the full amount of filler or thixotropic agent should be stirred in first. The hardening powder must always be stirred in and allowed to dissolve in the corresponding mixture or the pure resin. The stirring time will depend on the type and the condition of the mixing equipment used and on the temperature of the material.



    Application


    Acrydur ME05 is applied squeegee and/or trowel to the primed and scattered surface. The mix should be spread coarsely to the desired thickness using a trowel or squeegee and then should be compressed and smoothed using a large smoothing trowel so that no pores and trowel marks remain in the floor. This product is particularly suitable for areas with higher slope as the mix does not level by itself.

    The application of the system requires consistent and even technique to ensure the prevention of puddles and good compaction of the mix and to avoid pores and air bubbles within the stated tolerance of fillers and resin and depending on the thickness of the application.



    Product Details
    10154-975374

    Data sheet

    Manufacturer
    RSL
    For Use By
    Professional Use
    Interior / Exterior Use
    Interior & Exterior
    For Use On
    Concrete Floors
    Application Method
    Trowel
    Squeegee
    Single, Two or Three Pack
    Two-Pack
    Pack Size
    25kg
    190kg
    Interior/Exterior Use
    Interior & Exterior
    Mixing Ratio
    The base requires 1-6% hardening powder depending on site conditions
    Coverage
    Typically 2 kg/m2
    Max. Application Temperature
    30°C
    Min. Application Temperature
    0°C
    Density
    Approximately 0.98 g/cm3
    UN Number
    UN1866
    Layer Thickness
    Minimum 1 mm – 2.5 mm
    Pot Life
    Around 15 minutes from mixing
    Flashpoint
    10°C
    Base Type
    MMA
    Base Type
    Solvent-Free
    Suitable For Use On
    Concrete Floors
    Application Method
    Squeegee
    Application Method
    Trowel
    Components
    2K
    Product Usage Type
    Membrane
    Product Range
    Acrydur
    Hardening
    40 minutes or once surface has lost tackiness
    Category Guide
    FerFA Category 2/3
    Bond Strength
    1.5 MPa (Substrate failure)
    Water Penetration
    Impervious
    Colour Family
    Clear
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    RSL Acrydur ME05 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT