• RSL Resutile
  • RSL Resutile

RSL Resutile


Resutile ST and Clear is a hard-wearing, two-pack polyurethane floor coating which is designed to provide exemplary protection from any abrasion, chemicals or impact. It also removes graffiti.

  • Chemical resistant and UV stable
  • Abrasion, thermal shock and impact resistant
  • Hygienic & easy to clean
  • Impressive flexibility - high temperature resistance
  • Skydrol resistant
  • Choose from 450+ RAL, BS and standard colours
  • Delivery Options:
    • Standard colours (Black, Flint Grey, Salsa Red, Savannah, Stirling Grey, White, Forest Green, Kingfisher Blue and Poppy Red) are available with 7-10 Working Day Economy and Next Working-Day delivery options
    • All other colours are available on a 2-3 Working Day service only
    • Clear is available on a 7-10 Working Day service, with a minimum order quantity of 44 units

**Available for delivery - see Delivery Options below**

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
VAT excluded

£149.73 Tax incl.


Resutile ST & Clear is a high performance, two pack polyurethane floor coating which is designed to provide excellent chemical resistance and light fastness. It is a hard wearing and tough but flexible coating with very good resistance to impact, abrasion and high temperature. Resutile is regularly used in the aviation industry due to its excellent resistance to Skydrol.

Resin Surfaces Limited have over 20 years of experience in the Aerospace industry, and Resutile is the coating applied to these high-traffic areas.

It is resistant to engineering lubricants such as Hyjet and Skydrol. Resutile can be found at some of the UK's largest airports in baggage halls, cargo terminals and aircraft hangars, including London Heathrow, Manchester, Leeds Bradford, Gatwick and Luton.

With its anti-slip properties, it is also excellent for fire stations, production lines and any other vehicular areas. 


  • Aircraft hangars
  • Laboratories
  • Prisons and police cells
  • Chemical plants
  • Pharmaceutical areas
  • Medical and Healthcare
  • Anti-slip finishes
  • Graffiti removal

Ordering References

Resutile is available clear (Resutile Clear) or in a range of colours (Resutile ST) below, as well as over 450 RAL and BS colours:

Colour Nearest RAL Match Size Finish
Black RAL 9017 5L Gloss
Buff RAL 1002 5L Gloss
Flint Grey RAL 7005 5L Gloss
Marigold RAL 1005 5L Gloss
Salsa Red RAL 3011 5L Gloss
Savannah RAL 1032 5L Gloss
Stirling Grey RAL 7004 5L Gloss
White RAL 9003 5L Gloss


New Concrete Floors: New concrete must be clean, sound, dry and fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm² is required.

Timber Floors: Must be clean, sound and dry. Old clear varnish/topcoat must be removed/sanded prior to application, as it may affect the inter- coat adhesion with Resutile.

Existing Concrete Floors: Remove all dirt, oil, grease, old paints or any or other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Local repairs should be carried out using Resuscreed PA or Resuscreed 45.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

Where Resutile is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface. Where surfaces are found to be porous a primer coat may be required to achieve a uniform sealed surface.


Resutile may be applied direct to concrete or as a seal coat or top coat to a resin floor system specified in our datasheets where a primer is not required. When applied direct to porous substrates the surface may require priming. Dry surfaces may be primed with Resuseal WB Clear or Resuprime ST.

Where the relative humidity of the substrate exceeds 75%, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table.

ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat


The ambient temperatures of the area should not be allowed to fall below 10°c throughout application and curing. Surface temperature must be above 5°c.

Mixing: Pre-mix the base component to a uniform consistency then add the entire contents of the hardener to the base and mix by using a slow speed hand held powered mixer and mixing paddle for approximately two to three minutes to achieve consistent mixture.

Note: Do not use a separate mixing bucket as it may affect the mixing ratio.

Apply the whole mixed paint by using spreading rake, roller and brush to achieve the maximum coverage within the specified pot life time frame.

Do not add solvent to this product.

Slip resistance can be improved by lightly broadcasting anti slip aggregates on the first coat (after primer) whilst still wet and back rolling, at a rate of 50/100 g/m² . When cured apply the second Resutile coat to secure the aggregates. Alternatively, one pack of R.S. Beadgrip can be added to each pack of Resutile to achieve a fine non-slip texture.

Product Details

Data sheet

Interior / Exterior Use
For Use On
Concrete, Wood, Masonry Surfaces
Application Method
Roller, Brush, Rake
Clear, Standard / Ready Mixed, Fully Tintable
Single, Two or Three Pack
Pack Size
Rake, Roller, Brush
5 litres will cover 50m sq. @ 100 microns wet thickness.
Touch Dry
6 Hours
UN Number (Activator)
UN Number (Base)

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Be the first to ask a question about this product!

Question about the product

* Required fields
You might also like

RSL Resuseal WB

Resuseal WB is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish.  Low odour  Silica Free  Superb adhesion  Hard wearing  Hygienic Dust-free Some product colours are made to order and have minimum...

Price £54.79
In stock

RSL Resuprime ST

Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces.  Features and Benefits: Versatile for many types of application Excellent adhesive properties Easy to apply Can be used as a tack coat for screeds No...

Price £80.31
In stock

RSL Resuscreed 45

Resuscreed 45 is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be feather edged Can act as a repair system...

Price £58.23
In stock

RSL Resuprime MVT

RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood.  Easy application Use on...

Price £21.35
In stock

RSL Resuscreed PA

RSL Resuscreed PA (formerly known as Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Features and Benefits:  Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation...

Price £39.70
In stock