Resuflor WB (formerly known as Resuseal WB) is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish. These standard colours are readily available with faster shipping options; more colours are also available...
RSL Resutop - Standard Readily Available Colours
Resutop is a two-pack, high solids, high-build epoxy coating, that creates an attractive chemical resistant heavy-duty industrial floor.
- High-build finish - hygienic and easily cleaned, suitable for sterilising
- Good colour stability - smooth high gloss finish
- Low odour - hard wearing
- Anti-slip aggregate can be added
- Note: Stirling Grey and Flint Grey are readily available for order - for clear, see Resuflor HB Clear
- All other colours can be found at RSL Resutop - Special Colours which are currently made to order with minimum order quantities of 69 units and longer lead times
Resutop boasts exceptional adhesion qualities that can be applied to a plethora of substrates. It is designed to be unaffected by regular sterilisation, where cleanliness is imperative.
It can be made slip-resistant with additional aggregates, does not require ventilation for evaporation, and guarantees no shrinkage during curing.
It has a high gloss finish, with attractive light reflection and comes in a variety of colours.
Its low odour qualities, chemical resistance, oil resistance, and bacteria-free finish make it perfect for the food industry, pharmaceuticals, and automotive showrooms.
- Food processing and beverage areas
- Chemical plant rooms
- Engineering workshops
- Automotive & aviation areas
- Factory units
- Used as a seal coat for various Sherwin-Williams flooring systems
New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm sq. is required.
Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resuflor Patch or Resuflor Screed.
Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.
Where Resutop is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.
Where the relative humidity of a substrate exceeds 75% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.
The number of coats to be applied is chosen in accordance with the following table:
ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat
For Further information please refer to recommended individual product data sheets.
The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation.
Mixing: Pre-mix the coloured base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two to three minutes until the two components have fully combined.
The mixed unit should be applied immediately by squeegee, roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks. Coverage rates may vary depending on profile and porosity of the substrate.
- Interior / Exterior Use
- For Use On
- Application Method
- Brush, Roller, Squeegee
- Smooth Gloss
- Clear, Standard / Ready Mixed
- VOC Levels
- Low (50-149 g/l)
- Single, Two or Three Pack
- Pack Size
- Brush, Roller, Squeegee.
- 5 Kg. will cover 18.6m sq. @ 200 microns wet film thickness.
- Touch Dry
- 6 Hours
- UN Number (Activator)
- UN Number (Base)
Be the first to ask a question about this product!
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and...
Resuflor Screed (formerly known as Resuscreed 45) is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be...
RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood. Easy application Use on...
RSL Resuflor Patch (Formerly known as Resuscreed PA and Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Features and Benefits: Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum...
Resuflor HB Clear (formerly known as Resutop Clear) is a two-pack, high solids, high-build epoxy coating for application as a chemical resistant heavy duty floor coating, used as a clear sealer for decorative flooring systems such as Decora MS, producing a seamless, hard wearing, hygienic floor finish. Low odour Good colour stability...