• RSL Elladur™ SF
  • RSL Elladur™ SF
  • RSL Elladur™ SF

RSL Elladur SF


Elladur™ SF is a high-build, Polyaspartic/Polyurea fast-cure floor coating system designed to create an advanced, tough and durable gloss finish in a range of thicknesses.


  • Fast cure at low temperatures
  • Tough, yet flexible
  • Low odour
  • UV stable
  • High build
  • Can be used commercially/industrially
  • Can be used on a range of substrates
  • Refer to Ordering References below
  • Some colours have minimum order quantities and may have longer leads times due to being made to order
  • Current colour: Clear
Choose a colour
Close colour picker
  • Clear
  • White
  • Black
  • Poppy Red
  • Salsa Red
  • Stirling Grey
  • Flint Grey
  • Savannah Yellow
  • Kingfisher Blue
  • Forest Green
VAT excluded

£263.59 Tax incl.


Ordering References

Colour Nearest RAL Match Size Finish Mimimum Order Quantity
Clear - 5 KG Gloss 1
Black RAL 9017 5 KG Gloss 10
Flint Grey RAL 7005 5 KG Gloss 1
Salsa Red RAL 3011 5 KG Gloss 1
Savannah RAL 1032 5 KG Gloss 10
Stirling Grey RAL 7004 5 KG Gloss 1
White RAL 9003 5 KG Gloss 1
Forest Green RAL 6002 5 KG Gloss 10
Kingfisher Blue RAL 5017 5 KG Gloss 10
Poppy Red RAL 3020 5 KG Gloss 10

Some colours with minimum order quantities may also have longer leads times due to being made to order

The game-changing, technological Elladur SF and SF Clear are very versatile systems. They can be created with anti-slip finishes and decorative finishes by incorporating the relevant flakes and aggregates to your flooring needs.

Recommended Uses

  • Where a fast turnaround at a low temperature is required
  • Decorative floors
  • Domestic floors
  • Medical areas
  • Commercial environments
  • Industrial floors
  • Where high-build, UV stable coatings are needed


New Concrete Floors: New concrete must be clean, sound, dry and fully cured and surface laitance removed preferably by vacuum enclosed shot blasting or mechanical grinding. A minimum strength of 25N/mm sq. is required.

Timber Floors: Must be clean, sound and dry. Old clear varnish/topcoat must be removed/sanded and surface must be primed prior to application.

Existing Concrete Floors: Remove all dirt, oil, grease old paints or other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Local repairs should be carried out using Resuscreed PA or Resuscreed 45.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation, as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advise on intercoat adhesion and suitability, as it may not be compatible with the existing floor coating.

Where over-coating other systems such as epoxy coatings or screeds, as part of a specified composite system in the data sheets, please follow the recoat time as stated. These should be tack free, but not fully cured. If fully cured, then mechanical preparation is required to ensure intercoat adhesion.

Where Elladur SF is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.


Elladur SF may be applied to an existing resin floor system, where a primer is not required. When applied direct to porous substrates such as concrete, the surface must be primed with Elladur SF to ensure good adhesion to the surface.

Where the relative humidity of the substrate exceeds 75%, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

 ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
 85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat


Mixing: Pre-mix the base component to a uniform consistency, then add the entire contents of the hardener to the base and mix by using a slow speed electric mixer for approximately two minutes to achieve consistent mixture. Do not use a separate mixing bucket as it may affect the mixing ratio.

A rubber blade and/or a short-haired roller can work best for this application, to help avoid incorporating extra air and moisture in the coating. It is important to ensure that the recoat times are observed, with a maximum recoat of 8 hrs measured at 20°C substrate temperature and 50% relative humidity.

For other conditions please consult with our technical team. It is strongly recommended to apply the second coat as soon as the first coat has lost the tackiness to achieve the maximum adhesion. If the maximum recoating interval is exceeded, then the surface must be prepared and roughened to ensure intercoat adhesion.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details

Data sheet

Interior / Exterior Use
For Use On
Concrete, Wood
Clear, Standard / Ready Mixed
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Pack Size
5kg will cover between 6 to 20m2 depending on the applied thickness
Touch Dry
2-3 Hours

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Be the first to ask a question about this product!

Question about the product

* Required fields
You might also like

RSL Resuscreed 45

Resuscreed 45 is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. ADVANTAGES Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be feather edged Can act as a...

Price £59.30
In stock

RSL Resuprime MVT

RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood.  Features and Benefits:...

Price £19.80
In stock

RSL Resuscreed PA

RSL Resuscreed PA (formerly known as Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Features and Benefits:  Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation

Price £38.44
In stock