Bradite HD Floor + Wall is a high performance, two-pack, water-based epoxy floor and wall coating. For interior concrete, wood or steel requiring a tough, quick drying, hard wearing, easy to clean, flexible coating with excellent chemical and water resistance.
Available in 450+ in RAL & BS colours
Ideal for areas requiring regular deep clean and anti-graffiti finish
Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cart
High performance, two-pack, water-based epoxy floor and wall coating
For interior concrete, wood or steel floors and wall areas requiring a tough, quick drying, hard wearing, easy to clean, flexible coating with excellent chemical and water resistance
Ideal for areas requiring regular deep clean and anti-graffiti finish
Low odour during application makes it ideal for food preparation and hygiene areas including breweries and bakeries
Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems
Complies with BS 476 Part 6 & 7: Fire propagation index, I; 2.5, Surface spread of flame; Class 1, Building Regulations 1991, “Fire Safety”, Document B [para. A12(b)]: Class 0
Preparation
For internal steel, wood, concrete, ceramic and terracotta tiles and other absorbent mineral substrates which are dry, free of contamination, dust, efflorescence and properly prepared and primed.
Floor Preparation
Substrates should be dust free and completely dry before coating
When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance. If the concrete is loose, chipping or has concrete dust present, the coating will not perform properly unless all loose material and dust is removed and damaged areas are repaired
Power floated, shiny or unpainted non porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite Acid Etch TA37, or primed using Bradite Floor Primer ES40. Please consult the product data sheet for more details
High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate. Bradite TD39 industrial strength detergent should be used if necessary to remove all grease and oil
Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting. Substrate should be dust free and completely dry before coating
Cracks and pits should be filled using a suitable screed or mortar before painting. Substrate should be dust free and completely dry before coating
Wall Preparation - New building Or Total Repair
When painting new plaster it is vital to ensure the substrate is fully cured and free of laitance
Cracks and pits should be filled using a suitable filler before painting
Remove all loose and flaking paint back to a sound substrate
High gloss coatings should be abraded to provide a mechanical key
Substrate should be dust free and completely dry before coating
Bradite TD39 industrial strength detergent should be used with scrubbing, washing and rinsing to remove grease or oil
Industrial Protective Coating Preparation
High pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface
Bradite TD39 industrial strength detergent, washing and rinsing should be used with scrubbing to remove grease or oil
For new or total repair, steel should be blast cleaned to SIS Sa 21/2 minimum with a blast profile of 35-50 microns. (For maintenance repair, sweep blast or mechanically abrade existing coating to provide a key. Damaged or rusty areas should be blast cleaned to SIS Sa 21/2 or mechanically to SIS St 3 minimum)
Application
Painting System:
Thin first coat on new or uncoated concrete, wood or plaster by 20-30% to enable penetration and binding of substrate. Application and use should always conform to the codes of practice described in BS 6150 and BS 5493
For application on concrete, wood or other absorbent substrates, the first coat should be thinned 10-20% with water to allow penetration into the substrate [If Bradite Floor Primer ES40 has been used then the priming coat of Bradite HD Floor and Wall should be omitted]
For application on plaster or other absorbent substrates, the first coat should be thinned 10-20% with water to allow penetration into the substrate
For new or total repair, steel should be blast cleaned to SIS Sa 21/2 minimum with a blast profile of 35-50 microns. (For maintenance repair, sweep blast or mechanically abrade existing coating to provide a key. Damaged or rusty areas should be blast cleaned to SIS Sa 21/2 or mechanically to SIS St 3 minimum)
For maintenance painting the 1st coat will be a touch up to bare areas only
Applicable by brush, roller, conventional air spray and airless spray:
Brush and Roller – Supplied ready for use. Thin, if required, with 0 - 5% water. On smooth substrates, the use of a short pile roller is advised
Conventional Air Spraying - Thin with 10 - 20% clean water as required, tip size - 2.0mm, tip pressure 60psi (0.4MPa) approximately
Airless Spraying - Thin with 0-15% clean water as required, tip size - 18 thou (0.46mm) approximately, tip pressure - 2100 psi (15MPa) approximately
Clean all equipment immediately after use with water for best results
Suitable for use with Bradite Low Slip Hard Aggregate LS30, which should be added to the paint and mixed thoroughly just before use at a rate of 1 x 250ml LS30 tin (400g) per 5 litre of paint
Limitations
Compatibility with existing coatings should be confirmed by preparing and painting a test patch
This product is not suitable for applying over asphalt, bitumen, epoxy tar, alkyd, chlorinated rubber or vinyl based paints
This system is recommended for internal protection and decoration only. Epoxy systems will chalk on external exposure to sunlight, resulting in loss of gloss and colour fade
The end user and applicator must ensure that the finished floor is safe against slips in all likely usage conditions
Always refer to the Health and Safety sheet for the product before use, and observe the warning phrases on the label
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Bradite HD Floor + Wall is recommended for internal protection and decoration only. Epoxy systems will chalk on external exposure to sunlight, resulting in loss of gloss and colour fade.
Bradite HD Floor + Wall is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Bradite HD Floor + Wall is a high performance, two-pack, water-based epoxy floor and wall coating. For interior concrete, wood or steel requiring a tough, quick drying, hard wearing, easy to clean, flexible coating with excellent chemical and water resistance.
Available in 450+ in RAL & BS colours
Ideal for areas requiring regular deep...
We no longer stock this product, but can recommend Rust-Oleum 3366 Epoxy Powerfloat Floor Primer Rapid as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our...
Bradite Acid Etch is a mineral acid solution used as a pre-treatment for bare concrete surfaces, for application to bare concrete floors to remove excess lime and/or to etch a surface profile to smooth concrete.
Provides improved adhesion of subsequent floor coatings
Manufactured under the auspices of an ISO 9001:2008 quality & ISO...
Bradite Industrial Degreaser is an aqueous alkaline low foaming detergent used for degreasing contaminated surfaces prior to painting.
Ideally suited for degreasing oily or soiled surfaces and for removing road dirt
Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems
More...
Bradite Low Slip Additive (LS30) is a hard Aluminium Oxide aggregate additive providing additional under foot traction to floor coatings, used in conjunction with Bradite floor paints requiring a hard wearing low slip additive and added to the paint and mixed thoroughly just before use.
Manufactured under the auspices of an ISO 9001:2008...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3).
Please click here for important information about these kits.
Kit Contents:
SET 1 (Hand Tools)
1 x Rust-Oleum...