Bradite Epoxy Coating

EC88

Bradite Epoxy Coating is a tough and hard-wearing two-pack epoxy coating with water and chemical resistance. Ideal for use in refurbishing fibreglass swimming pools. Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems

  • Available in more than 350 colours in RAL & BS
  • Resistance to heavy traffic and chemicals
  • Ideal for water immersion
  • Surface dry in 3 hours
  • For interior use

Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

**Available for delivery - see Delivery Options below**

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
Size
Finish
£77.40
VAT excluded

£92.88 Tax incl.
Quantity

Description

Bradite Epoxy Coating is two-pack coating and paint system for concrete and suitably primed steel. Its main application is in water immersion and is therefore ideal for the refurbishment of fibreglass swimming pools. The resistance to chemicals and water make this a great epoxy coating of choice.

It should be noted however that this coating is not suitable for environments which are used for drinking water, or for fish ponds.

Can be used with Bradite Low Slip Additives SA12 or SA14 to provide additional under foot traction.

Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems. 2004/42/EC EU limit value for this product (cat.A/j sb): 500g/l (2010). This product contains max. 408 g/l VOC.


Features & Benefits

  • Available in more than 350 colours in RAL & BS
  • Superior resistance to heavy traffic and chemicals.
  • Forms a tough, hard-wearing film.
  • For interior use.
  • Semi-gloss finish.
  • Suitable for most water immersion (not to be used for drinking water
    or fish ponds).
  • Surface dry in 3 hours.


Preparation

For internal steel, wood, concrete and other absorbent mineral substrates which are dry, free of contamination, dust, efflorescence and have been properly prepared and primed. Compatibility with existing coatings should be confirmed by preparing and painting a test patch. Not suitable for applying over asphalt, bitumen, epoxy tar, alkyd, chlorinated rubber or vinyl based paints.

Substrates should be dust free and completely dry before coating. When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance.

Power floated, shiny or unpainted non porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite TA37, or primed using Bradite Floor Primer ES40. Please consult the product data sheet for more details.

High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate.

Bradite TD39 industrial strength detergent should be used if necessary to remove all grease and oil.

Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting.

Substrate should be dust free and completely dry before coating.

Cracks and pits should be filled using a suitable screed or mortar before painting.

Substrate should be dust free and completely dry before coating.


For application on concrete, wood or other absorbent substrates, the first coat should be thinned 10-20% with Bradite Thinner TE36 to allow penetration into the substrate (If Bradite Floor Primer ES40 has been used then the priming coat of Bradite Epoxy Coating Finish EC88 should be omitted).

Primer coat: Bradite Epoxy Coating Finish EC88 (thinned) if required.

2nd coat: Bradite Epoxy Coating Finish EC88.

3rd coat: Bradite Epoxy Coating Finish EC88.

For maintenance painting, the 1st coat will be a touch up to bare areas. 

Bradite Epoxy Coating Finish EC88 is suitable for use with Bradite Low Slip Additives SA14 or SA12, which can be either incorporated into the paint or hand broadcast into the applied wet paint. For more details about this, please consult the data sheet.


Application

Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.

Brush and Roller: Supplied ready for use. Thin, if required, with 0-10% Bradite Thinner TE36. On smooth substrates, the use of a short pile roller is advised.

Conventional Air Spraying: Thin with 10-25% Bradite Thinner TE36 as required, tip size - 2.0mm, tip pressure 60psi (0.4MPa) approximately.

Airless Spraying: Thin with 0 - 20% Bradite Thinner TE36 as required, tip size - 18 thou (0.46mm) approximately, tip pressure - 2100 psi (15MPa) approximately.

Cleaning Clean all equipment immediately after use with Bradite Thinner TE36 for best results.

Product Details
EC88

Data sheet

Manufacturer
Bradite
Interior / Exterior Use
Interior
Water / Solvent Based
Solvent
For Use On
Concrete, Wood, Steel
Application Method
Brush, Roller, Spray, Airless Spray
Sheen
Semi-Gloss
Colour
Fully, Tintable
Single, Two or Three Pack
Two-Pack
Product Certifications
ISO 9001:2008, ISO 14001:2004
Pack Size
5L
Application
Brush, Roller, Spray
Coverage
11m2 per Litre
Touch Dry
3 Hours
UN Number (Activator)
UN1263
UN Number (Base)
UN1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send