Rust-Oleum 5300 Epoxyshield Maxx is a 5 litre, gloss finish, water-based 2-component epoxy concrete floor coating with ultimate adhesion and durability on concrete.
A user friendly and easy to apply water-based 2 component epoxy floor coating with an ultimate adhesion and durability.
Maximum durability in just 1 coat
For medium to heavy traffic
Easy to apply, no primer required
Long-lasting gloss finish
Best possible car tyre resistance
Highly resistant against solvents and chemicals
Non-skid or decorative finish optional
The product has an excellent wear, impact and abrasion resistance like foot and vehicle traffic. Resists chemicals and standing water. The product can be applied on concrete floors, which are completely clean and dry. It is not recommended to apply on smooth/dense concrete or concrete containing a curing compound, which will prevent a good adhesion. Can also be applied on old good adhering coatings.
Recommended Use
Epoxyshield 5300 MAXX can be applied on concrete floors, which are completely clean and dry. It is not recommended to apply on smooth/dense concrete or concrete containing a curing compound, which will prevent a good adhesion. Epoxyshield 5300 MAXX can also be applied on old good adhering coatings. Epoxyshield 5300 MAXX Additives:
Epoxyshield Decorative Chips (505.0.43) are specially designed for use in combination with Epoxyshield 5300 MAXX. The chips adhere permanently on the floor when they are sprinkled in the wet coating. They give a decorative finish and will also mask dirt and rugosity.
Technical Data
Density:
1,27
Gloss Level:
Satin
Solids content in volume:
63.6%
Mixing Ratio:
Base : Activator = 3 : 1 (volume)
Drying Times At 20°C/RH 50%
Dry To Handle:
16 hours (suitable for light foot traffic)
Dry To Recoat:
24 hours (suitable for normal foot traffic and heavy items)
Pour the contents of A into B and stir thoroughly for at least 3 minutes. Allow mixed product to stand (see table) before rolling the coating on to the surface. Do not leave container in direct sunlight. Mix again before applying. The product must be used within 1 to 2 hours of initial mixing (pot life, see table). This time decreases at higher temperatures. Do not mix Paint Chips with Epoxyshield 5300 MAXX.
Application Conditions
Apply when air (ambient) temperature is 15-35ºC and relative humidity is below 80%.
Concrete floors take a long time to warm up; make sure the previous day has also been at least 15ºC prior to painting. Minimum floor temperature for painting is 13ºC. Painting in mid afternoon ensures the best cure.
Application and Thinning: Roller
After the full 60 minutes use a paint roller (20 cm) to apply an even coat of Epoxyshield 5300 MAXX onto the surface. Apply in sections of 1,5 x 1,5 m so that Epoxyshield Decorative Chips can easily be scattered on the freshly coated surface. Maintain a wet edge to prevent lap marks and gloss differences. Sprinkle the decorative paint chips onto the wet film (note: this step may be skipped if chips are not desired. This will not affect the performance of the coating). Immediately continue to coat the next section (note: fresh paint can be applied over the loose chips that lay outside the previously painted area). Only one coat is necessary.
Cleaning of Equipment / Spills
Wash all tools and equipment immediately with warm water and mild detergent. Allow any unused product to harden in the container and discard according to local regulations.
Remarks
Since the application time is only 1 - 2 hours (depending on temperature) it is advisable to apply the product with 2 persons. Have 1 person begin trimming edges and have another person begin rolling out the floor as specified.
Sealed concrete: dripping a small amount of water onto the surface. If the water beads, a sealer is present and paint may not adhere properly.
Moisture in the concrete: apply a sheet of plastic (e.g. garbage bag) to the floor. Tape down the edges and allow to set for 24 hours. If water droplets appear on the inside of the plastic or if concrete appears wet (darker in colour), moisture is trapped in the concrete.
Loose concrete or concrete dust: if the concrete is loose, chipping or has concrete dust present, the coating will not perform properly unless all loose material and dust is removed and damaged areas are repaired.
Floors treated with a levelling mortar or on anhydride floors.
Product Details
445-919232
Data sheet
Manufacturer
Rust-Oleum
For Use By
General Use
Interior / Exterior Use
Interior
Interior / Exterior Use
Interior
Water / Solvent Based
Water
Water / Solvent Based
Water
For Use On
Concrete
Application Method
Roller
Sheen
Gloss
Colour
Standard / Ready Mixed
VOC Levels
Low (50-149 g/l)
Single, Two or Three Pack
Two-Pack
Single, Two or Three Pack
Two-Pack
Pack Size
5L
Mixing Ratio
Base : Activator 3 : 1 (volume)
Dry to Recoat (at 20°C)
24 hours (suitable for normal foot traffic and heavy items)
Fully Cured (at 20°C)
24 hours (suitable for normal foot traffic and heavy items)
Pot Life (at 20°C)
1½ hours
Coverage
7m² per litre
Max. Application Temperature
35°C
Min. Application Temperature
15°C
Density
1,27
Solids by Volume
63.6%
VOC
53 g/l
Shelf Life (from date of manufacture)
5 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35° C.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Is this product suitable for a concrete garage floor that has been treated to a self-levelling compound prior? If OK, would I need to prime/treat the surface prior to the application of the product?
Answer from Rawlins’ Technical Team:
Assuming the self leveling compound is suitable to be overpainted, it is clean, dry, sound and prepared as detailed in the technical data sheet this could be used.
We would recommend checking the technical data sheet of the screed used to see if it states it is suitable to be overpainted or used as a wear layer.
Rich on 2021-10-10 23:26:07
Question:
What size holes will this fill, I have Some small raindrop craters from after the concrete was poured and tamped and a few bits around the edge
Answer from Rawlins’ Technical Team:
This and any floor paints will not fill imperfections in the floor, assuming the concrete floor is prepared as detailed in the technical data sheet these should be repaired with Rust-Oleum 5412 Epoxy Filler or removed while the floor is ground.
Gordon Fitton on 2021-09-01 19:55:05
Question:
What is meant by induction time? For Epoxy shield Maxx. Is it waiting time?? Thanks.G.F. Am needing an answer Asap, as doing the garage floor on Thursday September 2nd.early afternoon.
Answer from Rawlins’ Technical Team:
The induction time is the amount of time the product should be left after mixing before use.
Lee on 2021-08-01 21:12:14
Question:
I’ve used this for my garage with decorative flakes. Do I need a clear top coat?
Answer from Rawlins’ Technical Team:
No protective topcoat is required following application of Rust-Oleum 5300 Epoxyshield Maxx however should you wish to apply a clear protective topcoat for additional durability and scratch resistance then we could recommend Rust-Oleum 9200 Rust-O-Thane but this must be applied within 7 days otherwise there will be adhesion problems.
Elena on 2021-04-20 17:29:02
Question:
What type of roler do you recommend to apply this product? I also need a paint tray. Thank you
Answer from Rawlins’ Technical Team:
We would recommend the Floor Application Kit, this comes with solvent resistant rollers, paint brushes, a mixing paddle, plastic scuttle, roller frame and telescopic pole.
Nicholas Taylor on 2019-02-11 17:11:41
Question:
I have a barn covering 90sqm, the concrete floor was laid last summer. Part of the concrete in the entrance lays outside (10sq m) the rest internal. Which epoxy (or other) floor covering would you advise. It will be subject to vehicle use. Regards Nicholas Taylor
Question: what is the cure time of the pot life @ 10° C?
Answer from Rawlins’ Technical Team:
Rust-Oleum 5300 Epoxyshield Maxx should be applied when air (ambient) temperature is 15-35ºC and relative humidity is below 80%.
Concrete floors take a long time to warm up; make sure the previous day has also been at least 15ºC prior to painting. Minimum floor temperature for painting is 13ºC. Painting in midafternoon ensures the best cure.
At 15ºC you will have around 2 hours of pot life - full details of induction and application times are listed on page 1 of the TDS (Technical Data Sheet) which can be downloaded from the 'DATASHEETS' tab on the product page.
Rust-Oleum 5300 Epoxyshield Maxx is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
Rust-Oleum Epoxyshield Decorative Flakes (Chips) are intended for use with their Epoxyshield Garage Floor Coating or Epoxyshield Maxx however it can also be used with other Rust-Oleum Mathys Floor Coating Systems.
One sachet will cover approximately 25m²
Broadcast/Scatter the flakes by hand or sieve
Can be used in conjunction with...
Rust-Oleum Epoxyshield Anti-Slip Additive can be added to any of the Epoxyshield Floor Coatings range - Epoxyshield Ultra, Epoxyshield Sealer, Epoxyshield Maxx and Epoxyshield Garage Floor Coating to produce a non-skid surface.
Non-skid floor additive based on thermally split flint stones
Formulated for use with Epoxyshield floor coatings...
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.
Provides an economical way of making sure you will have what you need
Ideal for interior and exterior paint projects
Click to jump down to...
Floor Application Kit from Rawlins Paints provides all the application equipment needed to apply conventional floor paints and coatings to a professional standard. The application of floor coatings is often crucial to their performance, so it is important to use the right tools to ensure a lasting finish.
Each kit contains:
12" Roller,...
Paul on 2022-12-19 10:51:24
