Coo-Var Profloor Plus Cold Cure
Coo-Var Profloor Plus Cold Cure is a low temperature curing version of Coo-Var Profloor Plus. This two-pack, solvent free epoxy resin coating is designed to cure when the surface temperature is in the range 0 to 10°C. Coo-Var Profloor Plus Cold Cure is particularly valuable for applications at colder times of the year when the cure time of the normal Coo-Var Profloor Plus product is too slow. This product is also low odour so it can be used in a wide range of environments.
- Low temperature curing high build coatings are obtainable in one application
- Easily cleaned surfaces, unaffected by strong detergents
- Good colour stability
- Can be disinfected and sterilized
- Slip resistant and abrasion resistant finishes can be achieved
- Solvent Free
Coo-Var Profloor Plus Cold Cure is a low temperature curing version of the Coo-Var Profloor Plus product. This two-pack, solvent free epoxy resin coating is designed to cure when the surface temperature is in the range 0 to 10°C. Coo-Var Profloor Plus Cold Cure is particularly valuable for applications at colder times of the year when the cure time of the normal Coo-Var Profloor Plus product is much too slow.
Coo-Var Profloor Plus Cold Cure floor coating is suitable for use in most industrial environments, on concrete, polymer screeds, asphalt etc. and provides a durable, decorative, attractive and easily cleanable surface. The low temperature of cure makes this product particularly useful in the recoating of areas where it is difficult to maintain a surface temperature above 10°C during the application and curing period.
Being low odour, Coo-Var Profloor Plus Cold Cure is ideal for use in similar areas where Coo-Var Profloor Plus would be used e.g. the food industry for preparation, processing, storage areas, bakeries, dairies and breweries etc. where solvent based products are unsuitable. The hard wearing and chemical/oil resistant properties also make Coo-Var Profloor Plus Cold Cure ideal to use in showrooms, display areas, supermarkets, warehouses and workshops.
Coo-Var Profloor Plus Cold Cure should not be applied in temperatures above 15°C.
The base and the hardener should be conditioned at normal room temperature, this will make the mixing process easier. The working temperatures of the areas should not be allowed to fall below 0°C throughout the application and curing period, otherwise the cure of the material will be retarded and surface finish adversely affected.
Ensure that the floor area is clear and prepared, and that all equipment etc is readily available prior to mixing.
Mix the entire contents of the base with the hardener thoroughly, using a slow speed electric mixer. Take care to mix the product thoroughly but do not over mix as this will reduce working time with the product.
Coo-Var Profloor Plus Cold Cure systems offer excellent chemical resistance against dilute mineral acids, alkalis, detergent solutions and certain solvents.
Coo-Var Profloor Plus Cold Cure achieves the maximum chemical resistance on full cure. Avoid chemical contact or aggressive cleaning within five days of application. Remove chemical spillages as quickly as possible to prevent concentration by evaporation. Contact the Technical Department who can advise on resistance to specific chemicals.
Please Note: This product has a minimum order quantity of 20 x 5kg per colour and is subject to a 7 - 10 working day lead time. Special colours can be produced, but may be subject to a surcharge and extended lead times - Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Base Type
- Epoxy Resin
- 4-5m² per KG
- Recommended Thinner/Cleaner
- Thinners 16
- Solids by Volume
- Touch Dry
- 36 hours at 0°C
- UN Number
- Pot Life (at 10°C)
- 15 minutes
Be the first to ask a question about this product!