Axalta ViterFloor 300 SF Epoxy Floor Coating is a two pack epoxy, solvent free, high build coating for concrete floors.
For new and old concrete floors subject to heavy mechanical wear and/or chemical attack, in areas such as the food processing, brewing, pharmaceutical and heavy engineering industries
High gloss, easily cleaned finish
Wide colour range of over 350+ RAL and BS shades
Resistant to water, oils, weak solutions of non-oxidising acids, alkali and salt solutions, and temporary splashes of oxidising acids and bleaches - VOC free
Accepts light traffic after 16hrs @23°C (300µm dft)
Please note:Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cart
Axalta ViterFloor 300 SF Epoxy Floor Coating is a two pack epoxy, solvent free, high build coating for concrete floors.
This product is suitable for new and old concrete floors subject to heavy mechanical wear and/or chemical attack, in areas such as the food processing, brewing, pharmaceutical and heavy engineering industries.
Axalta ViterFloor 300 SF Epoxy Floor Coating has a high gloss, easily cleaned finish which is resistant to water, oils, weak solutions of non-oxidising acids, alkali and salt solutions. It is also resistant to temporary splashes of oxidising acids and bleaches.
Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Resistant to water, oils, weak solutions of non-oxidising acids, alkali and salt solutions, and temporary splashes of oxidising acids and bleaches
VOC free
Accepts light traffic after 48hrs @23°C (300µm dft)
Wide colour range of over 350+ RAL and BS shades
Product Specification
Technical Data
Axalta ViterFloor 300 SF Epoxy Floor Coating
Volume Solids
99 ± 1% (loss of trace volatiles may reduce figure)
VOC Content
Does not contain VOC’s
SG
1.38-1.42 kg/lt mixed (may vary with colour)
Storage Conditions
Store in dry, cool conditions and protect from frost
Shelf Life
Minimum 12 months if stored as above in unopened containers
Flash Point
Above 60°C
Pot Life
20-30 minutes when poured on the floor; approx. 15 minutes in the container
Film Thickness Range And Coverage
Film Thickness Range & Coverage
Dry Film Thickness
Wet Film Thickness
Theoretical Coverage
Minimum*
300 µm (0.30mm)
300 µm
3.3 m2/litre
Maximum*
500 µm (0.50mm)
500 µm
2.0 m2/litre
*See Product Notes. Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated
Drying Times
Drying Times
Applied to 300 microns DFT
23℃
Dust Dry
6hrs
Light Traffic
16hrs
Full Cure
7 Days
Recoating
Normal maximum 24 hrs*
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation
*Please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Surface Preparation
All surfaces must be clean, dry, and free from grease, oil, laitance, dust and other contamination
Hardener 2995 101 - 1 part by volume (1 part by wt.)
Mixing Instructions:
Components must be mixed thoroughly by using a mechanical mixer (with side scraper) before use
Add hardener in the correct proportions and mix thoroughly for a minimum of 2 minutes
Mix the material just before use, and consider the area to be coated and pot life of the material when deciding how many units are required
Note: do not scrape or pour out remaining residues of mixed material from the bottom and sides of the container onto the floor, as this material may be incompletely mixed and cause ‘soft spots’ in the applied floor coating
It is recommended that all material is stored at a temperature of approximately 20ºC for at least 24 hours prior to use, to aid mixing and application
Only apply in conditions of good ventilation which must be maintained during drying and curing
Do not apply when rain, mist, sleet or snow are imminent
During application and drying time of the paint coating, the surface should be dry, the relative humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
Paint temperature should ideally be at a minimum of 15ºC
Application Methods
This product is recommended for application by serrated or steel trowel, felt or mohair roller, with brush being used only where required to cut-in around edges or for very small areas
Pour out the mixed ViterFloor 300 onto the primed floor and spread with a suitable trowel
Level with a mohair or felt roller, wearing spiked shoes to walk across the wet coating
This solvent free material can be applied in excess of 500 µm, but where additional thickness is required, a second coat is recommended
Anti-Slip:
Dependent on the degree of anti-slip required, aggregate can be broadcast onto the wet coating surface and allowed to dry
Surplus non-adhering particles should then be brushed off and further coats of ViterFloor 300 applied (if required) to encapsulate the particles
Please note: The higher the degree of anti-slip, the lower the ease of cleaning will be
Application Temperatures:
Do not apply or cure below 5°C, temperatures above 10°C recommended
Health & Safety
Containers are provided with safety labels which should be observed
Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Product Details
5346-899107
Data sheet
Manufacturer
Axalta Coating Systems
For Use On
Concrete
Application Method
Trowel, Roller
Sheen
Gloss
Colour
Fully Tintable
VOC Levels
N/A
Single, Two or Three Pack
Two-Pack
Pack Size
12.5L
Mixing Ratio
Base 4 : Hardener 1 (by volume)
Coverage
3.3m²/litre @300µm, 2m²/litre @500µm
Recommended Thinner/Cleaner
Thinner 1031
Min. Application Temperature
5°C
Solids by Volume
99 ± 1% (loss of trace volatiles may reduce figure)
Shelf Life (from date of manufacture)
12 months
Recommended Dry Film Thickness
300 microns
Recommended Wet Film Thickness
300 microns
UN Number (Activator)
UN3082
UN Number (Base)
UN3082
Fully Cured (at 23°C)
7 days
Pot Life
20-30 minutes when poured on the floor; approx. 15 minutes in the container
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Axalta ViterFloor 300 SF Epoxy Floor Coating is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Axalta 1031 Thinner, for use with the Axalta range of coatings, has a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistency for application whether it be for brush, roller or spray. Can also be used for the cleaning of some surfaces prior to application of the coating...
Axalta ViterFloor 400 SF Floor Primer/Sealer is a two pack epoxy, solvent free clear primer/sealer for concrete floors.A clear primer/sealer for new and old concrete floors Use as a primer/sealer under ViterFloor 300 and ViterShield GPL, and as a clear sealer for bare concrete floors to prevent dusting and dirt contamination Resistant...