Coo-Var Profloor 2 Pack Epoxy Floor Paint
Coo-Var Profloor 2 Pack Epoxy Floor Paint is an exceptionally hard wearing water based 2 pack epoxy floor and wall coating. Dries to an off-gloss finish. Seven colours are available plus other colours to order. Aggregate is mixed with paint or sandwiched between two coats for an antislip version. This makes for a very versatile product.
- Ideal for use in heavy traffic areas for foot traffic, trucks, vans and forklifts, inside and outside.
- Can be used over stable existing paint coverings.
- Wood, concrete, masonry, asphalt and tarmac.
- Floors and walls.
- An anti slip option is available.
- Do not apply at temperatures below 10c
Coo-Var Profloor 2 Pack Epoxy Floor Paint is an exceptionally hard wearing water based 2 pack epoxy floor and wall coating. Dries to an off-gloss finish. Seven colours available plus other colours to order. Aggregate is mixed with paint or sandwiched between two coats for an antislip version.
Coo-Var Profloor 2 pack epoxy should be diluted with 500ml of clean water per 5kg pack. Profloor is ideal for use in heavy traffic areas for foot traffic, trucks, vans and forklifts, inside and outside. Profloor can be used over stable existing paint coverings. Can be used on wood, concrete, masonry, asphalt and tarmac. Can be used on floors and walls. An anti slip option is available. Do not apply at temperatures below 10c.
All surfaces should be clean, dry, sound and free from contaminants. Concrete - power floated, granolithic and smooth surfaces should be roughened first to provide a good "key" for the paint. This can be done mechanically by abrading or blasting, or chemically using Coo-Var Acid Etch. These processes will have the advantage in addition to preparing the surface of also removing dirt and laitance.
New concrete must be allowed to cure thoroughly which can take up to 3 months. Other surfaces have to be prepared and primed with the suitable primer for that substrate. Existing painted surfaces - Surfaces should be cleaned, degreased and sanded to ensure an adequate "key" is produced. Remove all loose and flaking material and treat bare areas as new substrate and prepare accordingly.
You should have two containers: one larger than the other and labelled Hardener. The other smaller one labelled Base. The contents of the pack marked Base are added to the contents of the larger pack marked Hardener and thoroughly mixed together, preferably by slow speed electric mixer. After mixing, add up to 500 mls clean tap water to the 5 kilo unit and mix again. This will make up one 5 kilo unit of Profloor Floorpaint.
As dictated by normal good painting practice. Do not apply if the temperature is likely to drop below 10°C during application or during the drying process. In confined spaces provide adequate ventilation during application and drying.
Apply direct to ordinary stable concrete. CooVar High Performance Primer should be used where the surface is smooth, polished or porous. On Metal use Teamac Epidox 2 Pack Zinc Phosphate Primer. Can be used on wood asphalt and tarmac.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Interior / Exterior Use
- Interior and Exterior
- Water / Solvent Based
- For Use On
- Wood, Concrete, Masonry Surfaces, Asphalt, Tarmac
- Application Method
- Brush, Roller
- Clear, Standard / Ready Mixed
- VOC Levels
- Ultra-Low (5-49 g/l)
- Single, Two or Three Pack
- Pack Size
- Base Type
- Brush, Roller
- Pot Life (at 20°C)
- 2-4 Hours
- 6-10m² per KG
- Recommended Thinner/Cleaner
- Solids by Volume
- Touch Dry
- 4 Hours
|jacky on 2019-10-16 11:19:54|| |
How long do we need to leave between coats?
The re-coating interval for Profloor 2 Pack Epoxy Floor Paint is a minimum 16 hours and a maximum 72 hours - after this time the cured coating would need abrading prior to another coat being applied.
|Richard Minter on 2019-09-02 07:46:56|| |
On a concrete power floated garage floor would you recommend one or two coats?
Power floated concrete should be roughened first to provide a good "key" for the paint. This can be done mechanically by abrading or blasting, or chemically using Coo-Var Acid Etch. Coo-Var Two Pack High Performance Primer should then be applied followed by 2 coats of Coo-Var Profloor 2 Pack Epoxy Floor Paint.
|Chris Woods on 2019-07-07 19:40:04|| |
Do you provide small test pots? We would like to carry out museum test (silver and coper tarnish tests) to see if this is suitable for a museum, checking for off-gassing after a suitable curing/drying period of several days.
Unfortunately samples are not available of this product but if you contact our Technical Team on 0113 2455450 (option 2) or [email protected] with full details of your requirements we should be able to advise on a system that would be suitable.
|Graeme Connelly on 2016-08-22 13:26:59|| |
Question: Does Coo-Var Profloor paint have shelf life?
2 years from date of manufacture.