- There are no more items in your cart
- Shipping Calculated at checkout
- Sub-Total(ex. VAT)(inc. VAT)£0.00£0.00
RSL Elladur MC, previously known as SofTop MC, is a clear two component aliphatic polyaspartic coating providing excellent abrasion resistance and improved scratch resistance with a matt finish.
- Slightly textured matt surface
- Scratch and abrasion resistant
- UV resistant
- Easy to apply, with low viscosity and good adhesion
- Fast cure
- Can be used as a clear top coat for SofTop SLR, SofTop SLR Flex
- Please note, a 7-10 working-day lead time applies
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
Quick Links - Click To Jump To Section:
Surface Preparation
New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm² is required.
Existing Concrete Floors: Remove all dirt, oil, grease, old product or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and making sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resuscreed PA.
Existing Floors (previously coated): All previous coatings and loose floor products must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with the existing floor coating.
Where Elladur MC is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.
Priming
Elladur MC is typically applied as a top coat onto SofTop systems. If applied direct to a substrate it should ideally be primed with a suitable primer such as SofTop LVP prior to application. Porous substrates may require double priming. See Sherwin-Williams System Sheets for recommended floor systems.
Where the Relative Humidity of a substrate exceeds 75% ERH Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203. The number of coats to be applied is chosen in accordance with the following table:
ERH% | Required Coating Thickness |
---|---|
75-85 | 1 coat of Resuprime MVT at 200 µm per coat |
85-92 | 2 coats of Resuprime MVT at 200 µm per coat |
92-97 | 3 coats of Resuprime MVT at 200 µm per coat |
Application
Mixing: Pour the entire contents of part B into the container of part A. Mix with a low speed (ca.300 rpm) electric drill and paddle for at least 3 minutes until homogenous. Scrape the sides and bottom of the container several times during mixing to ensure complete mixing. Keep the mixing head submerged to avoid entrapping air. Do not work out of the original container. Decant the mixed material into a fresh container and remix for another minute.
Apply Elladur MC immediately by roller, brush or squeegee with a consistent procedure. It is also important to maintain a wet edge with this product to minimise the risk of roller marks in the cured finish. Work evenly over surface ensuring it is fully wetted out and then roll to complete an even coating without any ponding.
Elladur MC is supplied in prepacked units. Before mixing precondition both A and B components to a temperature of approximately 15 to 20°C. The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 5°C and at least 3°C above the dew point. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation.
Data sheet
- Manufacturer
- RSL
- For Use By
- Industrial Use
- For Use On
- Concrete
- Application Method
- Roller, brush and squeegee
- Sheen
- Smooth gloss
- Single, Two or Three Pack
- Two-pack
- Pack Size
- 9.5 kg
- Dry to Recoat (at 20°C)
- 2-4 hours or once surface has lost tackiness
- Fully Cured (at 20°C)
- 7 days
- Pot Life (at 20°C)
- 20 minutes from mixing
- Coverage
- Typically 0.05-0.15 kg/m2
- Solids by Volume
- ~50%
- Recommended Dry Film Thickness
- 50 – 100 microns
- Recommended Wet Film Thickness
- 90 – 180 microns
- Dry for Light Traffic (at 20°C)
- 2 hours
- Dry for Full Traffic (at 20°C)
- 24 hours
- Suitable For Use On
- Concrete
- Suitable For Use On
- Masonry
- Application Method
- Squeegee
- Application Method
- Roller
- Application Method
- Brush
- Colour Family
- Clear
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
RSL Elladur MC is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT