Rust-Oleum 5090 Anti-Condensation Coating
Rust-Oleum 5090 Anti-Condensation Paint is a water absorbing coating to be used on ceilings and the upper parts of walls, where steam or water vapour formation occurs, in order to prevent condensation and dripping. It is intended as a one coat, airless application, but a more textured finish can be obtained by applying 2-3 coats.
Rust-Oleum 5090 Anti-Condensation Coating is a water absorbing coating for walls and ceiling, that is based on a water-based acrylic polymer. In containing a non-leaching fungicide, 5090 Anti-Condensation Paint offers excellent protection against mould growth.
- Recoatable after just 5 hours
- Application is possible on slightly damp surfaces
- Ideal for high humidity areas (breweries, wash and shower rooms, etc.)
- Stops walls and ceilings dripping from condensation and developing mould growth
This off-white, anti-condensation paint should be used on ceilings and walls, and is intended for one coat application by airless spray. Rust-Oleum 5090 can be used where steam or water vapour formation occurs, in order to prevent condensation and dripping.
1 litre of product will, after drying, absorb at least 400 grams of water!
Old coatings should be humidity resistant, if not, remove or seal with Rust-Oleum Grey Primer 5980.
Approvals: Mould resistance by Itec. Absorption by Ceripec.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
|Pat Rooney on 18/06/2018|| |
Is this product suitable for application to the underside of a corrugated iron shed roof?
Yes, assuming the surface is bare metal, after preparation (see product data sheet) apply Rust-Oleum Mathys Metal Cladding Primer followed by Rust-Oleum 5090 Anti-Condensation Coating.
Please note that Rust-Oleum 5090 Anti-Condensation Coating works in an environment where there is short term high humidity followed by longer periods when humidity can escape e.g. bathrooms. It cannot work where the humidity builds up and cannot then escape. So if this shed was closed and humidity built up a as a result of sunshine, you would still get condensation forming and then dripping down from ceiling.
|mandy thornton on 11/10/2016|| |
Question: Hi, is this paint safe to use in a child's bedroom? I am trying to find a paint for a small cold bedroom that is prone to condensation. I am having his walls insulated and then I need to paint the plastered walls. Is this paint appropriate and also what would I need to prime the plastered walls with in a room prone to condensation. many thanks
Rust-Oleum 5090 Anti-Condensation Coating is intended for commercial applications, for domestic projects we would recommend Thermilate InsOpaint Anti-Condensation Paint. Once dry, prime the bare plaster walls with 1 coat of Zinsser Gardz, followed by 2-3 coats as required of Thermilate InsOpaint Anti-Condensation Paint.
A problem solving coating for damp walls developed by Rust-Oleum. The paint is specially formulated to adhere and build a strong bond with the damp surface it is applied to, because it contains cement the moisture on the substrate actually helps the paint cure and become stronger coating.
Sika BituSeal S-115 is a post applied self-adhesive waterproofing sheet membrane. It is based on SBS (styrene-butadiene-styrene) modified bitumen, reinforced with polyester non woven fabric. It has a silicone-treated release liner on the upper and lower surface. Sika BituSeal S-115 is designed for use as an underlayer in fully self-adhesive multi-ply...
1901 Anti-Condensation Paint is a matt white paint that helps prevent the formation of condensation on walls and ceilings in rooms prone to airborne moisture such as bathrooms, wet rooms, communal shower/changing rooms and kitchens etc.
SikaProof P-12 is a fully and permanently bonded, self-adhesive, post-applied, composite sheet membrane waterproofing system for reinforced concrete structures. It consists of a flexible polyolefin (FPO) based membrane that is pre-coated with an adhesive sealant layer so that the membrane system is self-adhesive. It is cold- and post-applied, without heat...
SikaProof A Edge is a preformed L-shaped SikaProof A membrane sheet in 1m width folded in 50/50cm with a self-adhesive strip on both sides for a faster and easier application of perimeter edges, corners and connections. Used for damp-proofing, concrete protection and waterproofing for basements and other below ground concrete structures against ground...
Nu-Flame FR Anti-Bacterial Colourcoat is an Anti-Microbial finish with flame retardant properties. Protects against many commonly found bacteria (e.g. Salmonella and MRSA). Tested to BS 476 part 6 & 7 and satisfies Class ‘0’ Requirements of current Building Regulations. Advantages Flame retardant Contains an active Anti-Microbial For walls and...
Sika MonoTop 109 WaterProofing Mortar is a one-component cement based premixed mortar with brushable consistency. Ready to use (just add water), high quality, thin waterproof slurry coating, based on special cements and admixtures to provide a water resistant and damp-proof finish. Suitable for preventing dampness and water penetration in basements,...
Rust-Oleum Dacfill Frigo is a gas & vapour tight coating for walls and ceilings, ideal for use in cold stores. Rust-Oleum Dacfill Frigo has high vapour and gas tightness with permanent high elasticity of up to 400%. It offers resistance against sudden variations in temperature and exhibits high mechanical strength.
SikaProof A05, SikaProof A08 and SikaProof A12 are fully and permanently bonded, self-adhesive, composite sheet membrane waterproofing systems for reinforced concrete of the main structure. It consists of an embossed polyolefin (FPO) membrane laminated with a sealant grid and a non-woven fleece. Damp-proofing, concrete protection and waterproofing for...
The Sika Plaster Drainage Membrane is a 5mm high-density polyethylene cavity drainage studded membrane used for internal fixing to masonry, stone or concrete walls. Suitable for over-plastering/rendering with sand/cement or with Sika Whitewall one coat anhydrite plaster. Easy to cut, fix and seal, unique undercut stud design creates mechanical key for...
The Sika CD Anti-Lime Coating is a blend of high-grade silicates and wetting agents, held in suspension with water as a carrier. Once applied to the concrete surface, this unique product seals the concrete surface. Reduce “Free Lime” leaching from concrete surfaces, an effective Anti-lime coating to new concrete in Cavity Drain systems. Totally seals the...
SikaMur InjectoCream 100 is a new concept for the control of rising damp. It is a water repellent, silane-based emulsion. A simple application gun is used to inject the cream into a series of holes drilled into a mortar course. Once injected to the mortar course, SikaMur InjectoCream 100 will diffuse within the damp wall to form a water repellent barrier...