SikaProof A05, SikaProof A08 and SikaProof A12 are fully and permanently bonded, self-adhesive, composite sheet membrane waterproofing systems for reinforced concrete of the main structure. It consists of an embossed polyolefin (FPO) membrane laminated with a sealant grid and a non-woven fleece. Damp-proofing, concrete protection and waterproofing for...
Sika Cavity Drainage System Accessories
The Sika Cavity Drainage System utilises a high density polypropylene internal drainage membrane, the system is installed loose laid in flooring applications and attached to the wall with surface plugs in vertical installations. Here you can find the associated accessories used with the Sika Cavity Drainage System.
The Sika Cavity Drainage System creates a secondary internal wall and floor to control water after it has penetrated the structure. Utilising a high density polypropylene internal drainage membrane, the system is installed loose laid in flooring applications and attached to the wall with surface plugs in vertical installations. The system directs penetrating water into a drainage system and a collection sump before using a pump to discharge water from the building. Most suitable for sites where a bonding system cannot be used, cavity drain provides protection from the ingress of water, vapour and gases. Suitable for above and below ground usage.
Sika Cavity Drainage membranes can be used where site conditions or the design of the structure make it difficult to use Sika 1 Pre-Bagged Waterproofing System or other traditional tanking methods. Sika Internal Cavity Drainage membranes work on the principal of allowing water to penetrate the structure, collect it and manage it into a suitable drainage system for disposal. The membrane are fixed to the walls using special plugs with minimum surface preparation required to the substrate. Once the membrane is has been fitted, wall surfaces can be dry lined or plastered and the floors can be screeded.
Here you can find the associated accessories used with the Sika Cavity Drainage System, please refer to the 'Sika Cavity Drainage System Installation Guidelines' and 'Sika Cavity Drainage System Brochure' documents available to download from the 'DATASHEETS' tab above. It is important that the manufacturer is contacted before use of these systems as a site visit/written specification may be required prior to use of these systems to ensure correct installation and suitability for the project in question.
Other associated products include;
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Be the first to ask a question about this product!
Coo-Var Anti-Condensation Paint is a quick and easy protection of one-off areas that helps prevent the formation of condensation. ADVANTAGES Prevents the formation of condensation Inhibits unsightly mould growth Can be a finish or coated with emulsion or acrylic Interior use Biocide reduces discolouration
A waterproofing paint that is guaranteed to keep water out and contains a biocide that protects the dried coating against fungal degradation for a minimum of 5 years. This waterproof masonry paint can easily be applied to wet or dry surfaces creating a smooth, non-gritty finish.
A problem solving coating for damp walls developed by Rust-Oleum. The paint is specially formulated to adhere and build a strong bond with the damp surface it is applied to, because it contains cement the moisture on the substrate actually helps the paint cure and become stronger coating.
SikaMur InjectoCream 100 is a new concept for the control of rising damp. It is a water repellent, silane-based emulsion. A simple application gun is used to inject the cream into a series of holes drilled into a mortar course. Once injected to the mortar course, SikaMur InjectoCream 100 will diffuse within the damp wall to form a water repellent barrier...
Zinsser Perma-White paint is a durable, water-based, very low odour finish containing a biocide that protects the dried coating against mould and mildew - guaranteed for 5 years. It is ideally suited for any area of persistent high humidity, frequent temperature changes and poor air circulation.
Sika MonoTop 109 WaterProofing Mortar is a one-component cement based premixed mortar with brushable consistency. Ready to use (just add water), high quality, thin waterproof slurry coating, based on special cements and admixtures to provide a water resistant and damp-proof finish. Suitable for preventing dampness and water penetration in basements,...
Remmers Color SA plus is a high quality, interior wall paint with micro-silver as a film preservative against bacteria & mould. A high quality interior coating that is used in rooms that are at risk for mould or are already infested, e.g. in living rooms and bedrooms, hospitals, children's rooms, schools, kindergartens, offices, storage rooms, hotels,...
SikaProof P-12 is a fully and permanently bonded, self-adhesive, post-applied, composite sheet membrane waterproofing system for reinforced concrete structures. It consists of a flexible polyolefin (FPO) based membrane that is pre-coated with an adhesive sealant layer so that the membrane system is self-adhesive. It is cold- and post-applied, without heat...
The Sika CD Anti-Lime Coating is a blend of high-grade silicates and wetting agents, held in suspension with water as a carrier. Once applied to the concrete surface, this unique product seals the concrete surface. Reduce “Free Lime” leaching from concrete surfaces, an effective Anti-lime coating to new concrete in Cavity Drain systems. Totally seals the...
Sika BituSeal Primer is a bitumen solution primer to be used in conjunction with Sika BituSeal S-115 to increase adhesion and bond to the substrate. High adhesion and bonding ability on various substrates, good binding ability for dust and loose particles, ready to use by brush, roller or spray.
Rust-Oleum Dacfill Frigo is a gas & vapour tight coating for walls and ceilings, ideal for use in cold stores. Rust-Oleum Dacfill Frigo has high vapour and gas tightness with permanent high elasticity of up to 400%. It offers resistance against sudden variations in temperature and exhibits high mechanical strength.