Alternatively you can email our sales & support team on [email protected]
Coo-Var Anti-Damp Paint
350/P230/1
Coo-Var Anti-Damp Paint is a white, special low odour, efflorescence resistant, resin-based paint for application to damp interior walls and ceilings. Designed as a primer coat.
Coo-Var Anti-Damp Paint is a white, special low odour, efflorescence resistant resin-based paint for application to damp interior walls and ceilings. Designed as a primer coat containing an active reagent which combines with surface moisture and dampness. Contains a biocidal product for the preservation of the dry film and to reduce discolouration. Can be over-coated.
Recommended Uses
Plaster
Cement
Stone
Walls
Ceilings
Internally
Damp surfaces IF not saturated.
Preparation
All surfaces should be clean, sound and free from contaminants and grease. Can be applied to damp surfaces but ensure the surfaces are not saturated.
Scrape and brush the surface to remove any loose flaking material. Flat down glossy surfaces with abrasive paper. Treat any mould or lichen with a proprietary mould remover with a scraper or a stiff brush then treat again.
Remove sources of damp and repair structural problems prior to application. Ensure all sources of damp are repaired prior to treatment, this includes structural, plumbing faults and rising damp.
Application
Apply by brush, roller or spray.
Brush wash/thinner – White spirit
Recommended Dried Film Thickness Per Coat: 40 microns Recommended Wet Film Thickness Per Coat: 110 microns
Drying time
Touch dry 2 hours
Hard dry 8 hours
Overcoat time
12 hours or overnight
Estimated coverage: 9m²/litre.
NOTE: This paint will not cure the cause of dampness.
Please contact Rawlins Paints' Technical Support Team on0113 2455450for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
SikaProof P-12 is a fully and permanently bonded, self-adhesive, post-applied, composite sheet membrane waterproofing system for reinforced concrete structures. It consists of a flexible polyolefin (FPO) based membrane that is pre-coated with an adhesive sealant layer so that the membrane system is self-adhesive. It is cold- and post-applied, without heat...
A waterproofing paint that is guaranteed to keep water out and contains a biocide that protects the dried coating against fungal degradation for a minimum of 5 years. This waterproof masonry paint can easily be applied to wet or dry surfaces creating a smooth, non-gritty finish.
Rust-Oleum 5090 Anti-Condensation Paint is a water absorbing coating to be used on ceilings and the upper parts of walls, where steam or water vapour formation occurs, in order to prevent condensation and dripping. It is intended as a one coat, airless application, but a more textured finish can be obtained by applying 2-3 coats.
Remmers Color SA plus is a high quality, interior wall paint with micro-silver as a film preservative against bacteria & mould. A high quality interior coating that is used in rooms that are at risk for mould or are already infested, e.g. in living rooms and bedrooms, hospitals, children's rooms, schools, kindergartens, offices, storage rooms, hotels,...
Sika BituSeal Primer is a bitumen solution primer to be used in conjunction with Sika BituSeal S-115 to increase adhesion and bond to the substrate. High adhesion and bonding ability on various substrates, good binding ability for dust and loose particles, ready to use by brush, roller or spray.
SikaMur InjectoCream 100 is a new concept for the control of rising damp. It is a water repellent, silane-based emulsion. A simple application gun is used to inject the cream into a series of holes drilled into a mortar course. Once injected to the mortar course, SikaMur InjectoCream 100 will diffuse within the damp wall to form a water repellent barrier...
The Sika CD Anti-Lime Coating is a blend of high-grade silicates and wetting agents, held in suspension with water as a carrier. Once applied to the concrete surface, this unique product seals the concrete surface. Reduce “Free Lime” leaching from concrete surfaces, an effective Anti-lime coating to new concrete in Cavity Drain systems. Totally seals the...
The Sika HD20 Membrane is a high-density polyethylene, high capacity cavity drainage membrane principally for use on floors, providing high water flow with a deep stud profile designed to resist blockages caused by lime deposits. Ideally suited by heavy duty use on floors, impermeable to water, gas and vapour, fast track installation, can be over-screeded...
The Sika Standard Drainage Membrane is an 8mm polypropylene studded membrane used for internal fixing to masonry, stone or concrete walls, dry lined walls, and as a floor membrane where limited water passage is anticipated. Provides a fast track waterproofing solution for walls or floors, suitable for use above and below ground, impermeable to water, gas...
The Sika Cavity Drainage System utilises a high density polypropylene internal drainage membrane, the system is installed loose laid in flooring applications and attached to the wall with surface plugs in vertical installations. Here you can find the associated accessories used with the Sika Cavity Drainage System.
Nu-Flame FR Anti-Bacterial Colourcoat is an Anti-Microbial finish with flame retardant properties. Protects against many commonly found bacteria (e.g. Salmonella and MRSA). Tested to BS 476 part 6 & 7 and satisfies Class ‘0’ Requirements of current Building Regulations.
Advantages
Flame retardant
Contains an active Anti-Microbial
For walls and...
Rust-Oleum Dacfill Frigo is a gas & vapour tight coating for walls and ceilings, ideal for use in cold stores. Rust-Oleum Dacfill Frigo has high vapour and gas tightness with permanent high elasticity of up to 400%. It offers resistance against sudden variations in temperature and exhibits high mechanical strength.
1901 Anti-Condensation Paint is a matt white paint that helps prevent the formation of condensation on walls and ceilings in rooms prone to airborne moisture such as bathrooms, wet rooms, communal shower/changing rooms and kitchens etc.
Sika BituSeal S-115 is a post applied self-adhesive waterproofing sheet membrane. It is based on SBS (styrene-butadiene-styrene) modified bitumen, reinforced with polyester non woven fabric. It has a silicone-treated release liner on the upper and lower surface. Sika BituSeal S-115 is designed for use as an underlayer in fully self-adhesive multi-ply...
