RSL Resuflor Wall Gloss


Resuflor Wall Gloss (Formerly known as Resuseal Wall Gloss) is an aesthetic two-pack, hard-wearing, water-based epoxy wall coating with exemplary adhesion for concrete, wood and other surfaces.

  • Hygienic
  • Dust-free
  • Resistant to light chemical attack
  • Low odour
  • Decorative

£161.54(ex. VAT)
£193.85 (inc. VAT)
Please choose your colour
Please Contact our Technical Team on 0113 245 5450 (ext. 2) to Order this Product


Resuflor Wall Gloss (Formerly known as Resuseal Wall Gloss) has an attractive and hard-wearing finish and is versatile in the surfaces for which it is suitable. It can be applied over previously painted surfaces as well as a variety of new ones.

Recommended Uses

  • Concrete
  • Plaster
  • Brick
  • Ceramics
  • Blockwork
  • Detainment centres
  • Laboratories
  • Food production areas
  • Motor garages


Surfaces to be coated must be clean, sound, dry and free of any contaminants that could impair good adhesion. Hard smooth surfaces should be abraded or sanded to provide a mechanical key. Where open block work is to be coated, this should be filled and bag rubbed with a sand cement mix to create a continuous, smooth paintable surface.

Substrate temperature should be between 10-30°C with a relative air humidity of 70% maximum. Cold, high humidity and lack of air movement can cause a patchy finish, gloss reduction, a delay in curing and damage to final properties. To prevent this, ensure that good drying conditions and air ventilation prolong throughout the application and cure of the product.


Open and porous substrates will require priming. Resuflor WB Clear is recommended and depending on the porosity and texture of the surface to be primed, may require two coats. Resuflor WB Clear will not seal blockwork as it is a thin film primer.


Mixing: Pre-mix the base component to a uniform consistency, then add the entire contents of the hardener to the base. Mix by using a slow speed hand held powered mixer and mixing paddle for approximately two to three minutes to achieve consistent mixture.

Note: Do not use a separate mixing bucket as it may affect the mixing ratio.

The mixed unit should be applied immediately by roller or brush with a consistent procedure, cross-rolling to ensure even application and to minimise roller marks. Coverage rates will depend on the porosity of the substrate.

Do not add water to this product.

Do not apply Resuflor Wall Gloss on top of polyurethane coatings, as it may not adhere properly.

Product Details

Data sheet

Water / Solvent Based
For Use On
Concrete, Plaster, Brickwork, Ceramic Tiles
Application Method
Roller, Brush
Standard / Ready Mixed
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Pack Size
5KG, 10KG
Brush, Roller
5kg will cover 37m sq. @ 100 microns wet thickness.
Touch Dry
12-24 Hours
UN Number (Base)

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Be the first to ask a question about this product!

Question about the product

* Required fields
You might also like

RSL Resuflor WB - Standard Readily Available Colours

Resuflor WB (formerly known as Resuseal WB) is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish.  These standard colours are readily available with faster shipping options; more colours are also available...

Price £179.39 (ex. VAT)
In Stock and Available for Delivery