PPG Sigma EP 110 Primer

    0660
    PPG4192

    PPG Sigma EP 110 Primer is a two-component, zinc phosphate blast primer/sealer for use in industrial or coastal atmospheres, with excellent rust preventing properties and curing at temperatures down to 5°C (41°F).

    • Excellent rust preventing properties in industrial or coastal atmospheres
    • Cures at temperatures down to 5°C (41°F)
    • Excellent adhesion to steel
    • Epoxy blast primer for steel
    • Registered as Highway Agency item 110
    • Approved Network Rail RT 98 item 7.1.2

    Colour
    Size
    Finish
    £81.19(ex. VAT)
    £97.43 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    PPG Sigma EP 110 Primer, a two-component, zinc phosphate blast primer/sealer with excellent rust preventing properties in industrial or coastal atmospheres, curing at temperatures down to 5°C (41°F). Registered as Highway Agency item 110 and approved Network Rail RT 98 item 7.1.2.



    Features & Benefits


    • Excellent rust preventing properties in industrial or coastal atmospheres
    • Cures at temperatures down to 5°C (41°F)
    • Excellent adhesion to steel
    • Epoxy blast primer for steel
    • Registered as Highway Agency item 110
    • Approved Network Rail RT 98 item 7.1.2

     

    ReferenceColourSizeGloss Level
    239497BS 08C354 litresEggshell
    239485BS 08C3520 litresEggshell



    Product Data


    Data for mixed product at 20°C (68°F)
    Number of componentsTwo
    Mass density1.4 kg/l (11.7 lb/US gal)
    Volume solids43 ± 2%
    VOC (Supplied)UK PG 6/23(92) Appendix 3: max. 554.0 g/l (approx. 4.6 lb/US gal)
    Recommended dry film thickness25 - 50 µm (1.0 - 2.0 mils) depending on system
    Theoretical spreading rate17.2 m²/l for 25 µm (690 ft²/US gal for 1.0 mils)
    Pot life8 hours at 20°C (68°F)
    Dry to touch20 minutes
    Overcoating IntervalMinimum: 4 hours
    Maximum: 3 months
    Full cure after5 days
    Shelf lifeBase: at least 12 months when stored cool and dry
    Hardener: at least 12 months when stored cool and dry

    Notes:

    • Refer below for more details on spreading rate and film thickness, overcoating intervals and curing times



    Surface Preparation


    Recommended Substrate Conditions and Temperatures

    Substrate conditions

    • Steel; blast cleaned to ISO-Sa2½, blasting profile 50 – 100 µm (2.0 – 4.0 mils)
    • Galvanized steel; pre-treated with Sigma Etch

    Substrate Temperature & Application Conditions


    • Substrate temperature during application and curing down to 5°C (41°F) is acceptable
    • Substrate temperature during application and curing should be at least 3°C (5°F) above dew point
    • Relative humidity during application and curing should not exceed 85%



    Application


    Instructions for Use

    Mixing ratio by volume: base to hardener 75:25 (3:1)

    • The temperature of the mixed base and hardener should preferably be above 15°C (59°F), otherwise extra thinner may be required to obtain application viscosity
    • Adding too much thinner results in reduced sag resistance and slower cure
    • Thinner should be added after mixing the components



    Induction time


    • None

     

    Air Spray


    Recommended thinner

    Volume of thinner

    • 0 - 5%, depending on required thickness and application conditions

    Nozzle orifice

    • 1.5 – 3.0 mm (approx. 0.060 – 0.110 in)

    Nozzle pressure

    • 0.3 - 0.4 MPa (approx. 3 - 4 bar; 44 - 58 p.s.i.)

     

    Airless Spray


    Recommended thinner

    • THINNER 91-92

    Volume of thinner

    • 0 - 5%, depending on required thickness and application conditions

    Nozzle orifice

    • Approx. 0.43 - 0.58 mm (0.017 - 0.023 in)

    Nozzle pressure

    • 15.0 MPa (approx. 150 bar; 2176 p.s.i.)

     

    Brush/roller


    Recommended thinner

    • THINNER 91-92

     

    Cleaning Solvent




    Spreading Rate and Film Thickness


    Spreading rate and film thickness

    DFTTheoretical spreading rate
    25 µm (1.0 mils)17.2 m²/l (690 ft²/US gal)
    35 µm (1.4 mils)12.3 m²/l (493 ft²/US gal)
    50 µm (2.0 mils)8.6 m²/l (345 ft²/US gal)

     

    Overcoating interval for DFT up to 160 µm (6.3 mils)


    Overcoating with...Interval10°C (50°F)20°C (68°F)30°C (86°F)
    ItselfMinimum8 hours4 hours3 hours
    Maximum3 months3 months2 months

     

    Curing time for DFT up to 50 µm (2.0 mils)


    Substrate temperatureDry to touchDry to handleFull cure
    10°C (50°F)40 minutes2 hours7 days
    20°C (68°F)20 minutes1 hour5 days
    30°C (86°F)15 minutes30 minutes3 days

    Note:

    Adequate ventilation must be maintained during application and curing (please refer to information sheet 1433 and 1434)



    Safety Precautions


    • For paint and recommended thinners, see information sheets information sheet 1430, information sheet 1431 and the relevant Material Safety Data Sheets in the attachments section above
    • This is a solvent-borne paint and care should be taken to avoid inhalation of spray mist or vapor, as well as contact between the wet paint and exposed skin or eyes



    References


    Product Details
    4192-553340

    Data sheet

    Manufacturer
    PPG
    Single, Two or Three Pack
    Two-Pack
    Parts
    Two
    Base Type
    Solvent-borne
    Solvent
    Epoxy
    Mixing Ratio
    3:1
    Suitable Substrates
    Steel, Galvanized steel
    Key Features
    Excellent rust preventing properties in industrial or coastal atmospheres, curing at temperatures down to 5°C (41°F).
    Application
    Brush, Roller, Spray
    Touch Dry (at 20°C)
    20 minutes
    Dry to Handle (at 20°C)
    -
    Dry to Recoat (at 20°C)
    4 hours
    Fully Cured (at 20°C)
    5 days
    Pot Life (at 20°C)
    8 hours
    Coverage
    17.2 m²/l for 25 µm (690 ft²/US gal for 1.0 mils)
    Recommended Thinner/Cleaner
    THINNER 91-92/THINNER 90-53
    Unit Contents
    Base & hardener
    Compatible Primers
    Sigma Etch
    Compatible Topcoats
    -
    Max. Application Temperature
    -
    Min. Application Temperature
    5°C (41°F)
    Density
    1.4 kg/l (11.7 lb/US gal)
    Solids by Volume
    43 ± 2%
    Heat Resistance (up-to)
    -
    VOC
    UK PG 6/23(92) Appendix 3: max. 554.0 g/l (approx. 4.6 lb/US gal)
    Shelf Life (Once Opened)
    Base & hardener: 12 months when stored cool and dry
    UN Number (Activator)
    UN1263
    UN Number (Base)
    UN1263
    Base Type
    Solvent Based
    Base Type
    Epoxy
    Suitable For Use On
    Galvanised Steel
    Suitable For Use On
    Steel
    Finish
    Eggshell
    Application Method
    Brush
    Application Method
    Spray
    Application Method
    Roller
    Usages
    Atmospheric
    Usages
    Zinc Phosphate
    Usages
    Anti-Corrosive
    Product Usage Type
    Primer
    Product Range
    Sigma EP
    Colour Family
    Beige
    Dry to Recoat (@ 20-25°C)
    4 hours
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    PPG Sigma EP 110 Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    PPG Thinner 90-53

    This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info

    Price £35.18 (ex. VAT)
    In Stock and Available for Delivery

    PPG Thinner 91-92

    This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info

    Price £36.75 (ex. VAT)
    In Stock and Available for Delivery

    PPG Sigma Etch

    We no longer stock this product, but can recommend Axalta ViterWash T Etch Solution as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113...

    In stock