PPG SigmaGlide 890

    7399
    PPG4173

    PPG SigmaGlide 890 is a two-component, silicone-based finish for fouling release systems on ships, installations and seawater intakes under all fouling conditions, for new-building or maintenance.

    • Non-toxic
    • Can be used at temperatures above 5°C (41°F)
    • No induction time
    • Can be applied by spray
    • Can be overcoated after 2 hours
    • See below for more information on surface preparation, application details and curing times
    • More colours may be available on request, depending on quantity
    • Please note: This product is no longer available

    Colour
    Size
    Finish
    Quantity
    Product not available
    In Stock and Available for Delivery (See Delivery Options Below)

    The minimum purchase order quantity for the product is 22.

    Description

    PPG SigmaGlide 890, a two-component, silicone-based finish for fouling release systems on ships, installations and seawater intakes under all fouling conditions. The non-toxic coating can be used at new-building or maintenance, applying by spray.

    Please note: This product is subject to a minimum order quantity of 440L and has an approximate delivery lead time of 21-28 days.

    Features & Benefits


    • Non-toxic, fouling release coating for ships, installations and seawater intakes under all fouling conditions
    • For use at new-building or maintenance
    • Can be used at temperatures above 5°C (41°F)
    • No induction time
    • Can be applied by spray
    • Can be overcoated after 2 hours
    • See below for more information on surface preparation, application details and curing times

     

    ReferenceColourSizeGloss Level
    236471Red Brown20 litresGloss

    Product Data


    Two-component, silicone-based finish for fouling release system

    Data for mixed product at 20°C (68°F)
    Number of componentsTwo
    Mass density1.1 kg/l (9.2 lb/US gal)
    Volume solids77 ± 2%
    VOC (Supplied)Directive 1999/13/EC, SED: max. 196.0 g/kg
    max. 215.0 g/l (approx. 1.8 lb/US gal)
    Recommended dry film thickness150 µm (6.0 mils)
    Theoretical spreading rate5.1 m²/l for 150 µm (206 ft²/US gal for 6.0 mils)
    Dry to touch1 hour
    Overcoating IntervalMinimum: 2 hours
    Refloating timeMinimum: 8 hours
    Shelf lifeBase: at least 36 months when stored cool and dry
    Hardener: at least 36 months when stored cool and dry
    Pot life4 hours at 20°C (68°F)

    Notes:

    • Refer below for more details on spreading rate and film thickness, overcoating intervals and curing times

    Surface Preparation


    Recommended Substrate Conditions and Temperatures

    Substrate conditions

    • Steel; blast cleaned to ISO-Sa2½ for excellent corrosion protection
    • For new-buildings or spot/full blast, SIGMAGLIDE 890 should only be applied over SIGMAGLIDE 790
    • As a refresh coat, SIGMAGLIDE 890 can be applied over itself in line with PPG Protective & Marine Coatings

     

    SIGMAGLIDE General Working Procedure


    • Previous coat must be dry and free from any contamination

     

    Substrate Temperature & Application Conditions


    • Substrate temperature during application and curing should be above 5°C (41°F)
    • Substrate temperature during application and curing should be at least 3°C (5°F) above dew point
    • Relative humidity during application and curing should be between 40% and 85%

    System Specification


    In order to achieve optimal performance from the SIGMAGLIDE system, the individual SIGMAGLIDE products must be applied in strict accordance with the minimum specified dry film thickness and also with the PPG Protective & Marine Coatings SIGMAGLIDE General Working Procedure. Please consult our technical team on 0113 2455450 or [email protected] for details of the application procedure which has been prepared to the best of our knowledge and in accordance with worldwide application best practices in order to ensure optimal workmanship and application results.

    Application


    Instructions for Use

    Mixing ratio by volume: base to hardener 80:20 (4:1)

    • Open drum just before use
    • Stir base well before use for 5 minutes
    • Add hardener to the base and stir well again for at least 5 minutes
    • No thinner should be added
    • All equipment must be thoroughly cleaned prior to use and before re-use with other materials, to prevent contamination
    • Overspray on paint, which will not be recoated with the SIGMAGLIDE 890, should be avoided as much as possible

     

    Induction Time


    None.

     

    Airless Spray


    Recommended thinner

    • No thinner should be added

    Nozzle angle

    • 35° – 60°, depending on nozzle orifice

    Nozzle orifice

    • Approx. 0.43 – 0.53 mm (0.017 – 0.021 in)

    Nozzle pressure

    • 15.0 - 20.0 MPa (approx. 150 - 200 bar; 2176 - 2901 p.s.i.)

     

    Brush/roller


    • For small areas only (touch up and repair)

     

    Cleaning Solvent


    Note:

    • The used cleaning solvent must not be allowed to contaminate other paints

     

    Overcoating interval for DFT up to 150 µm (6.0 mils)


    Overcoating with...Interval10°C (50°F)20°C (68°F)30°C (86°F)40°C (104°F)
    ItselfMinimum3 hours2 hours1 hour1 hour
    Maximum8 hours8 hours8 hours8 hours

    Notes:

    • Surface should be dry and free from any contamination
    • Relative humidity should be above 40%

     

    Pot Life (at application viscosity)


    Mixed product temperaturePot life
    10°C (50°F)6 hours
    20°C (68°F)4 hours
    30°C (86°F)2 hours

    Safety Precautions


    • For paint and recommended thinners, see information sheets information sheet 1430, information sheet 1431 and the relevant Material Safety Data Sheets in the attachments section above
    • This is a solvent-borne paint and care should be taken to avoid inhalation of spray mist or vapor, as well as contact between the wet paint and exposed skin or eyes

    References


    Product Details
    4173-890836

    Data sheet

    Manufacturer
    PPG
    For Use On
    Steel
    Application Method
    Spray
    Sheen
    Gloss
    Colour
    Standard / Ready Mixed
    Single, Two or Three Pack
    Two-Pack
    Pack Size
    20L
    Parts
    Two
    Base Type
    Solvent-borne
    Solvent
    Silicone
    Mixing Ratio
    4:1
    Suitable Substrates
    Steel
    Key Features
    For fouling release systems on ships, installations and seawater intakes under all fouling conditions
    Application
    Spray
    Touch Dry (at 20°C)
    -
    Dry to Handle (at 20°C)
    -
    Dry to Recoat (at 20°C)
    2 hours
    Fully Cured (at 20°C)
    -
    Pot Life (at 20°C)
    4 hours
    Coverage
    5.1 m²/l for 150 µm (206 ft²/US gal for 6.0 mils)
    Recommended Thinner/Cleaner
    THINNER 90-83 or 50/50 mixture of THINNER 21-06 and THINNER 50-02
    Unit Contents
    Base & hardener
    Compatible Primers
    SIGMAGLIDE 790
    Compatible Topcoats
    -
    Max. Application Temperature
    -
    Min. Application Temperature
    5°C (41°F)
    Density
    1.1 kg/l (9.2 lb/US gal)
    Solids by Volume
    77 ± 2%
    Heat Resistance (up-to)
    -
    VOC
    Directive 1999/13/EC, SED: max. 196.0 g/kg max. 215.0 g/l
    Shelf Life (from date of manufacture)
    Base & hardener: 36 months
    UN Number (Activator)
    UN1263
    UN Number (Base)
    UN1263
    Base Type
    Solvent-Borne
    Application Method
    Spray
    Product Usage Type
    Antifouling
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    PPG SigmaGlide 890 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    PPG Thinner 21-06

    This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info

    Price £38.18 (ex. VAT)
    In Stock and Available for Delivery

    PPG Thinner 90-83

    This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info

    Price £151.80 (ex. VAT)
    In Stock and Available for Delivery