Teamac Marine Matting Agent

509/G100/2579

Teamac Marine Matting Agent, is a matting additive that allows the sheen level of all colours of Teamac Marine Gloss to be customised.

Advantages

  • Allows Marine Gloss sheen levels to be customized.
  • Use to produce a range of finishes Matt, Eggshell, Satin & Semi-Gloss
  • Ideal for use where low glare is required such as boat roofs and interior head linings.
  • When added to Teamac Marine Gloss it is suitable for Yachts, Power Boats, Dinghies, Narrowboats and many other marine structures.
  • Can also be used with Teamac Metalcote.
  • It can be applied to suitably prepared Wood, GRP, Steel, Aluminium and Ferro Concrete.
  • Click to jump down to Technical Data

**Available for delivery - see Delivery Options below**

Size
£6.85
VAT excluded

£8.22 Tax incl.
Quantity

Description

Teamac Marine Matting Agent, is a matting additive that allows the sheen level of all colours of Teamac Marine Gloss to be customised.



Click To Jump To Section:




Features & Benefits


Advantages

  • Allows Marine Gloss sheen levels to be customized.
  • Use to produce a range of finishes Matt, Eggshell, Satin & Semi-Gloss.
  • Ideal for use where low glare is required such as boat roofs and interior head linings.
  • When added to Teamac Marine Gloss it is suitable for Yachts, Power Boats, Dinghies, Narrowboats and many other marine structures.
  • Can also be used with Teamac Metalcote.
  • It can be applied to suitably prepared Wood, GRP, Steel, Aluminium and Ferro Concrete.
  • Click to jump down to Technical Data



Product Specification


Technical Data
Volume Solids Approx 50%
VOC Content Max 530 g/litre
SG 0.98 @ 20 °C
Viscostity 3.5 Poise @ 25 °C
Flash Point Above 32 °C (closed cup)



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum 35 to 40 μm 80 μm 12 m2/litre @ 35 microns D.F.T



The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 4 Hours
Dry To Handle: 12 Hours
Dry To Recoat: 12 hours or overnight
Fully Cured: 5 - 7 Days



Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Surface Preparation


  • All surfaces should be clean, dry, sound and free from contaminants.
  • Existing painted surfaces should be cleaned, degreased and sanded to ensure an adequate "key" is produced.
  • Remove all loose, flaking material and treat bare areas as new substrate then prepare accordingly.



Preceeding Coat


  • N/A



Mixing


  • Mix well before use.



Application Conditions


  • As dictated by normal good painting practice.
  • Care must be taken during application that the temperature is above the dew point to avoid any contamination.
  • In confined spaces, provide adequate ventilation during application and drying.



Application Methods


Method Airless Spray Conventional Spray Brush Roller
  Yes No Yes Yes



  • Thinner (Max vol): N/A
  • Nozzle Size: 0.011"
  • Nozzle Pressure: 1800 to 2000 psi
  • Cleaning Solvent: Thinners 14



Mixing


  • Mix well before use.



Remarks


To achieve the required level of gloss reduction the following guideline has been created.  It is important to note that the performance of the product will be similar to the original gloss, however, the opacity of the chosen finish will be affected where the Matting Additive is increased and may require multiple coats to achieve full opacity. 

All reductions are approximate and testing on a non-critical area should be carried out to ensure the required sheen level has been achieved prior to full application. 

Matt appearance may vary from the original colour.

Recommended guidelines are as follows:

  • 25% addition by volume will achieve around a 35% reduction in gloss
  • 50% addition by volume will achieve around an 80 to 85% reduction in gloss
  • 75% addition by volume will achieve around a 90 and 95% reduction in gloss.



Health & Safety


See safety data sheet - SDS 20642 in the attachments link above.

Click to go back to the top of the page

Product Details
509/G100/2579

Data sheet

Manufacturer
Teamac
Water / Solvent Based
Solvent
For Use On
Wood, GRP, Steel, Aluminium, Ferro Concrete
Single, Two or Three Pack
Single
Pack Size
500ml
Suitable Substrates
Suitably prepared Wood, GRP, Steel, Aluminium and Ferro Concrete
Touch Dry (at 20°C)
4 Hours
Dry to Handle (at 20°C)
12 Hours
Dry to Recoat (at 20°C)
12 hours or overnight
Fully Cured (at 20°C)
5 - 7 Days
Coverage
12 m²/litre
Recommended Thinner/Cleaner
Teamac Thinner 14
Solids by Volume
Approx 50%
VOC
Max 530 g/litre
Recommended Dry Film Thickness
35 to 40 μm
Recommended Wet Film Thickness
80 μm
UN Number
UN1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Teamac Thinner 14

A specially formulated blend of solvents designed to mix with its compatible Teamac or Coo-Var coating to create an optimal consistancy for application. Suitable for use with Brush, Roller or Spray. Teamac Thinner 14 can also be used for the cleaning of some surfaces prior to application of the coating. Also suitable for the cleaning of...

Price £9.23
In stock

Teamac Metalcote Plant Enamel

Teamac Metalcote Plant Enamel, is a tough, flexible enamel paint with an attractive gloss finish and excellent durability. It has good resistance to lubricating, mineral oils, many common industrial chemicals and heat. Advantages Good resistance to oils, chemicals and heat Ideal for use on all types of machinery including tractors...

Price £20.26
In stock

Teamac Metalcote Undercoat

Teamac Metalcote Undercoat. A full bodied, high opacity undercoat suitable for use with Teamac Metalcote Plant Enamel paint, used as a primer or undercoat on bare or previously painted surfaces, gives a matt finish, presents a good surface and enhances topcoat. High opacity pigments. Primer or undercoat. Good coverage and fast drying....

Price £19.12
In stock

Teamac Marine Gloss

Teamac Marine Gloss is a high quality, modified long oil alkyd marine coating. It has excellent gloss and opacity. High gloss Excellent opacity and adhesion Touch dry in as little as 4 hours (at 20°C) Full hardness in 5 - 7 days Suitable for all general marine areas, bridge fonts, deck work, masts, superstructures etc Click to jump...

Price £23.04
In stock