Teamac - Deck Paint Smooth
  • Teamac - Deck Paint Smooth

Teamac Deck Paint Smooth

534/G150/ ALL

Teamac Deck Paint Smooth, is a conventional, durable, protective coating for wood and metal decks.  It can be used on suitably prepared wood and metal decks as well as directly to GRP decks.

Advantages

Colour
Size
Finish
£29.28
VAT excluded

£35.14 Tax incl.
Quantity

Description

Teamac Deck Paint Smooth, is a conventional, durable, protective coating for wood and metal decks.  Teamac Deck Paint Smooth can be used on suitably prepared wood and metal decks and can also be applied directly to GRP decks.



Click To Jump To Section:




Features & Benefits


Advantages



Product Specification


Technical Data
Volume Solids 50 to 52.6%
VOC Content Max 394.04 g/litre
SG 1.17 to 1.31 °C
Viscostity 4.5 Poise @ 25 °C
Flash Point Above 32 (closed cup)



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum 35 to 40 μm 75 μm 13 m12/litre @ 35 microns D.F.T



The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 5 Hours
Dry To Handle: 24 Hours
Dry To Recoat: 12 hours or overnight
Fully Cured: 5 - 7 Days



Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Surface Preparation


  • Ensure all surfaces are clean, dry and free from grease, oil and any other contaminates.
  • GRP should be abraded prior to coating to ensure an adequate "key" is produced.
  • Existing painted surfaces should be cleaned, degreased and sanded to ensure an adequate "key" is produced.
  • Remove all loose, flaking material and treat bare areas as new substrate then prepare accordingly.



Preceeding Coat




Mixing


  • Mix well before use.



Application Conditions


  • As dictated by normal good painting practice.
  • In confined spaces, provide adequate ventilation during application and drying.



Application Methods


Method Airless Spray Conventional Spray Brush Roller
  Yes No Yes Yes



  • Thinner (Max vol): Brush/Roller: Thinners 14 (10%) - Airless Spray: Thinners 14 (10%)
  • Nozzle Size: 0.013"
  • Nozzle Pressure: 1800 to 2000 psi
  • Cleaning Solvent: Thinners 14





Health & Safety


See safety data sheet - SDS 10492 in attachments section above.

Click to go back to the top of the page

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
534/G150/ ALL

Data sheet

Manufacturer
Teamac
Suitable Substrates
Suitable for wood, metal and GRP
Key Features
Easy to apply. Protective. Good durability.
Application
Brush, Roller, Spray
Dry to Handle (at 20°C)
24 Hours
Dry to Recoat (at 20°C)
12 hours or overnight
Fully Cured (at 20°C)
5 - 7 Days
Coverage
13m² per litre
Recommended Thinner/Cleaner
Teamac Thinner 14
Solids by Volume
50 to 52.6%
VOC
Max 394.04 g/litre
Touch Dry
5 Hours
Finish
Semi-Gloss
Size
5 litre, 20 litre
Recommended Dry Film Thickness
35 to 40 μm
Recommended Wet Film Thickness
75 μm
UN Number
1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Teamac Aluminium Wood Primer

Teamac Aluminium Wood Primer, is an oil based primer that contains aluminium.  Used primarily to prevent staining on knotted or resinous timber, but also acts as an excellent heavy duty primer. Suitable for Narrowboats, Cruisers, Barges, Yachts and other Marine Applications.  It can be applied to suitably prepared timbers and boards....

Price £19.32
In stock

Teamac Thinner 14

A specially formulated blend of solvents designed to mix with its compatible Teamac or Coo-Var coating to create an optimal consistancy for application. Suitable for use with Brush, Roller or Spray. Teamac Thinner 14 can also be used for the cleaning of some surfaces prior to application of the coating. Also suitable for the cleaning of...

Price £11.72
In stock

Teamac Wood Primer White

Teamac Wood Primer White, is a general purpose, modified alkyd based wood primer for wood, especially useful for priming soft wood. It can be applied to suitably prepared timbers and boards. Overcoatable in 16 hours, it is compatible with Teamac Marine Gloss. Traditional Wood Primer For All Type of Wood. Provides Flat Finish For...

Price £16.61
In stock

Coo-Var Aluminium Wood Primer

Coo-Var Aluminium Wood Primer is an oil based primer that contains aluminium. Used primarily to prevent staining on knotted or resinous timber. Easy to apply. Product Features Also works as a heavy duty primer Resists resin staining Resists blistering of topcoats Interior/Exterior use Semi-matt finish

Price £20.69
In stock

Teamac Zinc Phosphate Primer

Teamac Zinc Phosphate Primer, An anticorrosive primer on iron and steel, for use with a range of conventional topcoats such as Teamac Marine Gloss and Teamac Metalcote Plant Enamel. Can be used for: Marine purposes Fire escapes Fetal gates Metal garage doors Ideal in coastal areas Click to jump down to Technical Data

Price £14.12
In stock
16 other products in the same category:

Jotun Jotaguard 630

Jotun Jotaguard 630 is a two component polyamine cured epoxy coating that is a fast drying, surface tolerant, hard wearing, high solids, high build product. Specially designed for general use in cargo holds and can be used as primer or finish coat in atmospheric and immersed environments. 

Price £146.37
In stock

PPG SigmaCover 456 HS

PPG SigmaCover 456 HS is two component high solids polyamide cured recoatable zinc phosphate epoxy primer/coating. This general-purpose epoxy primer/coating is available in 350+ colours from RAL and BS, for steel and concrete structures in atmospheric exposure that can be recoated with various two-component and conventional coatings, even...

Price £462.00
In stock

Jotun Jotaguard 690 S

Jotun Jotaguard 690 S is a two component polyamine cured pure epoxy coating that is a fast drying, high solids, high build product. It has excellent abrasion, impact and scratch resistant and is specially designed as a premium finish coat for cargo holds where extended repair intervals are required, even when operating with the toughest exposure.

Price £210.60
In stock

International Interzone 1000

International Interzone 1000 is one of the most proven and reliable glass flake epoxies on the market today, with documented in-service performance dating back almost 30 years. International Interzone 1000 provides outstanding abrasion and corrosion resistance to steelwork located in the harshest offshore and inland environments.

Price £433.16
In stock

International Interzone 954BG

International Interzone 954BG is a two component, low VOC, high solids, modified epoxy barrier coating that will continue to cure when immersed in water and has excellent cathodic disbondment resistance. Specifically designed to provide long term steel protection via brush or roller application techniques where the performance of Interzone 954 is required...

Price £103.49
In stock

Jotun Marathon 500

A surface tolerant from Jotun that is a high build epoxy coating suitable for environments with very high corrosivity, such as areas in the splash or tidal zones. Jotun Marathon 500 is a two component polyamine cured epoxy coating. It's a surface tolerant, high solids, high build product that will continue to cure even when immersed in water.

Price £214.50
In stock

Jotun Jotaguard 690

Jotun Jotaguard 690 is a two-component polyamine cured pure epoxy coating that is fast drying and has superb mechanical strength. ADVANTAGES Easy to clean Long lasting Reduced application costs Impact/abrasion resistant Less downtime Certificated

Price £179.01
In stock

International Interzone 954 (Rapid Cure)

International Interzone 954 (Rapid Cure) is a faster drying version of Interzone 954 to be used in tidal areas where immersion will be rapid. Designed for use in offshore splashzone maintenance, where its continued cure under immersed conditions makes it ideal for coping with tidal movements and surges. May be applied to reoxidised and...

Price £98.71
In stock

Teamac Bilge Paint

Teamac Bilge Paint, provides protection for the inside surfaces of the hull below the water line.  A resilient and hardwearing single pack coating providing available in 4 colours. Advantages Hardwearing and resilient Single Pack formulation Use on inner hull walls Suitable for use on wood, metal and GRP Click to jump down to...

Price £14.50
In stock

Teamac Black Tar Varnish

Teamac Black Tar Varnish, is a synthetic tar varnish for industrial, agricultural and marine use. It is used for the protection of (weathered) wood, metal and other surfaces, inside or outside and should be used on barns, farm buildings, roofs etc. and marine applications. Advantages Synthetic tar varnish Weathered surface protection...

Price £32.29
In stock

Jotun Jotaguard 660

Jotun Jotaguard 660 is a two component polyamine cured pure epoxy coating that is a fast drying, surface tolerant, very abrasion and impact resistant, high solids, high build product. Specially designed as a high performance coating for cargo holds it can be used as primer or finish coat in atmospheric and immersed environments.

Price £162.51
In stock

International Interzone 954

International Interzone 954 is a two component, low VOC, high solids, modified epoxy barrier coat designed for use in offshore splashzone maintenance, where its continued cure under immersed conditions makes it ideal for coping with tidal movements and surges. May be applied to reoxidised and slightly damp surfaces.

Price £98.71
In stock

Teamac Marine Matting Agent

Teamac Marine Matting Agent, is a matting additive that allows the sheen level of all colours of Teamac Marine Gloss to be customised. Advantages Allows Marine Gloss sheen levels to be customized. Use to produce a range of finishes Matt, Eggshell, Satin & Semi-Gloss Ideal for use where low glare is required such as boat roofs and...

Price £12.96
In stock

Carboline Carboclean Gel 100

Carboline Carboclean Gel 100 is a biologically degradable surface cleaner without any hazardous substances. Can be disposed to drains/sewage systems without containment. Top Features Removes rust, chalk, magnetite, salt, algae and other deposits. Well-suited for treatment of ceilings, walls. Works as a treatment of metals and...

Price £30.38
In stock

International Interlac 668

International Interlac 668 is a one pack, alkyd based, high visibility coating for application to marker buoys and as a safety marker on board ship. International Interlac 668 is for use at Newbuilding, Maintenance & Repair or On Board Maintenance.

Price £127.64
In stock

Teamac Boot-topping

Teamac Boot-topping, is an interface coating for use between the waterline and the deck coatings, provides a hard surface less receptive to marine growth and is polish-able to remove grime. Advantages Easy to apply Water and weather resistant Industrial grade marine coating Very hard wearing solid finish Click to jump down to...

Price £13.33
In stock