International Intersleek 717

    BXA716/A15LT
    INT4820

    International Intersleek 717, is a two pack foul release system linkcoat.

    • Enables application of the Intersleek 700 and Intersleek 900 foul release systems over SPC antifoulings
    • For use at maintenance & repair
    • Hard dry in as little as 3 hours (at 25°C)
    • Dries down to 0°C in 24 hours
    • Good application rate of 5.4 m²/litre at 100 microns dft

    Colour
    Size
    Finish
    £644.63(ex. VAT)
    £773.56 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    International Intersleek 717, is a two pack foul release system linkcoat, enabling application of the Intersleek 700 and Intersleek 900 foul release systems over SPC antifoulings.



    Quick Links - Click To Jump To Section:




    FeaturesBenefits


    • To enable application of the Intersleek 700 and Intersleek 900 foul release systems over SPC antifoulings.
    • For use at maintenance & repair.



    Product Information


    Colour

    • BXA716-Mid Brown

    Finish/Sheen

    • Matt

    Part B (Curing Agent)

    • BXA717

    Volume Solids

    • 54% ±2% (ISO 3233:1998)

    Mix Ratio

    • 2.50 volume(s) Part A to 1 volume(s) Part B

    Typical Film Thickness

    • 100 microns dry (185 microns wet)

    Theoretical Coverage

    • 5.4 m²/litre at 100 microns dft, allow appropriate loss factors

    Method of Application

    • Airless Spray, Brush, Roller

    Flash Point (Typical)

    • Part A 42°C; Part B 31°C; Mixed 37°C

    Induction Period

    • Not required

    Shelf Life

    • 12 months at 25°C. Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.



    Drying Information


    0°C15°C25°C35°C
    Touch Dry [ISO 9117/3:2010]140 minutes90 minutes40 minutes15 minutes
    Hard Dry [ISO 9117-1:2009]24 hours7 hours3 hours2 hours
    Pot Life180 minutes105 minutes75 minutes45 minutes



    Overcoating Data


    See limitations - click to jump to section

    Substrate Temperature
     0°C15°C25°C35°C
    Overcoated ByMinMaxMinMaxMinMaxMinMax
    Intersleek 731--5 hours2 days4 hours2 days3 hours2 days
    Intersleek 737--6 hours2 days5 hours2 days4 hours2 days



    Note: The minimum temperature at which Intersleek 717 may be overcoated with Intersleek 731 is 15°C. * Refer to the Intersleek application guidelines for details on application of Intersleek 737 down to 0°C.



    Regulatory Data


    VOC

    • 411 g/lt as supplied (EPA Method 24)
    • 343 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC).

    Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.



    Systems Compatibility


    Consult our technical team on 0113 2455450 (option 2) or send a message to [email protected] for the system best suited for the surfaces to be protected.



    Surface Preparations


    • Use in accordance with the standard Worldwide Marine Specifications.
    • All surfaces to be coated should be clean, dry and free from contamination.
    • High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.
    • Intersleek 717 should always be applied over an approved antifouling and/or anticorrosive scheme. Areas of breakdown, damage etc. should be prepared to the specified standard (eg. Sa2½ (ISO 8501-1:2007)) and patch primed with Intershield 300. The Intersleek 717 link coat scheme should then be applied over all.



    Application


    Mixing

    Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified.

    • (1) Agitate base (Part A) with power agitator
    • (2) Combine entire contents of curing agent (Part B) with base (Part A) and mix thoroughly with power agitator.

    Thinner

    • International GTA220
    • Thinning is not normally required
    • Consult our technical team on 0113 2455450 (option 2) or send a message to [email protected] for advice during application in extreme conditions.
    • Do not thin more than allowed by local environmental legislation.

    Airless Spray

    • Recommended
    • Tip Range 0.66-0.79 mm (26-31 thou)
    • Total output fluid pressure at spray tip not less than 211 kg/cm² (3000 p.s.i.)

    Brush/Roller

    • Application by brush/roller is recommended for small areas only

    Cleaner

     

    Work Stoppages and Cleanup

    • Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with International GTA822. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units.
    • Clean all equipment immediately after use with International GTA822. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature, relative humidity and elapsed time, including any delays.
    • Do not exceed pot life limitations.
    • All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.

     

    Welding

    In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.



    Safety


    All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations.

    Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product.

    Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.



    Limitations


    Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult our technical team on 0113 2455450 (option 2) or send a message to [email protected] for specific recommendations.

    Apply in good weather. Temperature of the surface to be coated must be at least 3°C above the dew point. For optimum application properties bring the material to 21-27°C, unless specifically instructed otherwise, prior to mixing and application.

    Unmixed material (in closed containers) should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet.

    Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments.

    As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.

     

    Product Details
    4820-808830

    Data sheet

    Manufacturer
    International
    For Use By
    Professional Use
    Application Method
    Brush, Roller, Airless Spray
    Sheen
    Matt
    Colour
    Standard / Ready Mixed
    Single, Two or Three Pack
    Two-Pack
    Pack Size
    15L
    Parts
    Two parts
    Mixing Ratio
    2.50 volume(s) Part A to 1 volume(s) Part B
    Coverage
    5.4 m²/litre at 100 microns dft, allow appropriate loss factors
    Recommended Thinner/Cleaner
    International GTA220
    Compatible Primers
    Intershield 300
    Density
    Part A: 1.32 - Part B: 0.93
    Solids by Volume
    54%
    VOC
    411 g/lt
    Shelf Life (from date of manufacture)
    12 months at 25°C. Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.
    Touch Dry
    140 minutes (0°C) - 90 minutes (15°C) - 40 minutes (25°C) - 15 minutes (35°C)
    Recommended Dry Film Thickness
    100 microns
    Recommended Wet Film Thickness
    185 microns wet
    UN Number
    UN1263
    Pot Life
    180 minutes (0°C) - 105 minutes (15°C) - 75 minutes (25°C) - 45 minutes (35°C)
    Suitable For Use On
    SPC Anti-Foulings
    Finish
    Matt
    Application Method
    Brush
    Application Method
    Spray
    Application Method
    Roller
    Product Usage Type
    Link Coat
    Product Range
    Intersleek
    Colour Family
    Brown
    Categorised As
    Marine Paints > Antifouling Primers & Tie Coats
    Seasonal
    Cold Weather
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    International Intersleek 717 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    International Thinner/Equipment Cleaner GTA220

    International Thinner/Equipment Cleaner GTA220 is used for thinning compatible International products. It can also be used for the general cleaning of surafces and equipment after using the associated paint or coating. More Information Delivery Info

    Price £52.44 (ex. VAT)
    In Stock and Available for Delivery

    International Thinner/Equipment Cleaner GTA822

    International Thinner/Equipment Cleaner GTA822 is used for thinning compatible International products. It can also be used for the general cleaning of surafces and equipment after using the associated paint or coating. More Information Delivery Info

    Price £52.44 (ex. VAT)
    In Stock and Available for Delivery

    International Intershield 300

    With a proven 21 years` track record on over 8,700 projects, International Intershield 300 is the offshore industry benchmark in anti-corrosive performance. This unique abrasion resistant, pure epoxy coating, with an aluminium content >9%, offers long term asset protection to offshore structuresUnparalleled long term corrosion and...

    Price £520.27 (ex. VAT)
    In Stock and Available for Delivery