Teamac Duracote Red Oxide Paint

519/G150/65
TEA234

Teamac Duracote Red Oxide Paint, is a general purpose primer and finish in one. Teamac Duracote Red Oxide Paint can be used coat on coat direct on to metal and can be used indoors or outdoors and is a very good protector of metals.

Please Note: 20L Pack size is subject to a MOQ of 4 units

Coverage Calculator

Colour
Size
Finish
£18.08(ex. VAT)
£21.70 (inc. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

Teamac Duracote Red Oxide Paint, is a general purpose primer and finish in one.  Teamac Duracote Red Oxide Paint can be used coat on coat direct on to metal and can be used indoors or outdoors and is a very good protector of metals.



Click To Jump To Section:




Features & Benefits


Suitable to be used on:



Product Specification


Technical Data
Volume Solids 49%
VOC Content 399 g/litre
SG 1.16 @ 20°C
Viscostity 4.5 Poise @ 25°C
Flash Point Above 32°C (closed cup)



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum 35 - 40 μm 75 μm 13 m2/litre @ 40 microns D.F.T.



The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 2 hours
Dry To Handle: 12 hours
Dry To Recoat: 12 hours or overnight
Fully Cured: 5 - 7days



Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Surface Preparation


  • Ensure all surfaces are clean, dry and free from grease, oil and any other contaminates.
  • Bare steel should be free from dust, rust and scale. Blast cleaning to SA 2½ is recommended.
  • If blast cleaning is impractical, mechanical cleaning should be employed as hand cleaning does not clean the steel to the required degree.
  • Any oil or grease should be removed with Coo-Var Degreaser before de-rusting.
  • Where blast cleaning is carried out after assembly, special attention must be paid to edges, corners, nuts, bolts, welds etc.
  • Welds should, if necessary be ground and all weld spatter, slag etc. must be removed.



Preceeding Coat




Subsequent Coat


  • Teamac Duracote Anticorrosive Red Oxide or other suitable topcoat.



Mixing


  • Mix well before use.



Application Conditions


  • As dictated by normal good painting practice.
  • Care must be taken during application that the temperature is above the dew point to avoid any contamination.
  • In confined spaces, provide adequate ventilation during application and drying.



Application Methods


Method Airless Spray Conventional Spray Brush Roller
  Yes No Yes Yes



  • Thinner (Max vol): Thinners 14 (10%)
  • Nozzle Size: 0.011" - 0.013"
  • Nozzle Pressure: 1800 to 2000 psi
  • Cleaning Solvent: Thinners 14



Health & Safety


See safety data sheet - SDS 10583 in the attachments section above.

Click to go back to the top of the page

Product Details
234-183006

Data sheet

Manufacturer
Teamac
Interior / Exterior Use
Interior & Exterior use
Interior / Exterior Use
Interior and Exterior
Water / Solvent Based
Solvent
For Use On
Steel
Application Method
Brush, Roller, Airless Spray
Sheen
Gloss
Colour
Standard / Ready Mixed
Key Features
All round metal protector. Self over-coatable
Dry to Handle (at 20°C)
12 Hours
Dry to Recoat (at 20°C)
12 hours or overnight
Fully Cured (at 20°C)
5 - 7 Days
Coverage
13m² per litre
Recommended Thinner/Cleaner
Teamac Thinner 14
Solids by Volume
49%
VOC
399 g/litre
Touch Dry
5 Hours
Finish
Gloss
Size
1 litre, 2.5 litre, 5 litre
Recommended Dry Film Thickness
35 - 40 μm
Recommended Wet Film Thickness
75 μm
UN Number
UN1263
Base Type
Solvent-Based
Suitable For Use On
Steel
Finish
Gloss
Application Method
Spray
Application Method
Roller
Application Method
Brush
Product Type
Primer & Topcoat
Product Range
Duracote
Colour Family
Red
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Bob on 2023-07-31 20:45:05
Question: 

So I have applied one coat to side of narrowboat, scabbled down to steel then sanded to bare metal. The data sheet says it can be reapplied coat on coat, with the weather as poor as it is this year I’m waiting to apply second coat. Does it need to keyed prior to another coat or can it just be over coated on itself ?. And can I just key it each year and apply another coat as and when required?. Thank you

Answer from Rawlins’ Technical Team: 

This product can be applied coat on coat.

However, if the previous coat has fully cured, which takes around 5 days at 20 Degrees ░, you'll need to abrade the existing coating, which will ensure the subsequent coat can adhere successfully.

questions Mark on 2021-03-25 17:06:51
Question: 

As daft as this may sound, is this product aquatic friendly? I need something to paint a galvanised roof of my koi pond. If this isn’t suitable, can you recommend a product that is please?

Answer from Rawlins’ Technical Team: 

This paint is not aquatic friendly, assuming the galvanised is bare, clean, dry, sound and prepared as detailed in the Technical Data sheet (treated with Teamac Mordant Solution (T Wash) prior to application ) we can recommend Teamac Metaclor Antifouling Primer followed by Teamac Chlorvar Chlorinated Rubber Paint.

Once fully cured this is will be fine for aquatic life.

questions matt on 2019-09-22 15:07:53
Question: 

Would this be a good product to use on sea water vessels to protect the steel keels?

Answer from Rawlins’ Technical Team: 

In this sort of environment you would be better using Teamac Zinc Phosphate Primer on the topsides and Teamac Metaclor Underwater CR Primer anywhere below the waterline.

questions Neil Tulloch  on 2018-10-01 18:55:21
Question: 

Is one coat ok or do you recommend two

Answer from Rawlins’ Technical Team: 

Teamac Duracote Red Oxide Paint can be applied directly to prepared iron or steel, a minimum of 2 coats are recommended when leaving as a finish. Alternatively one coat can be applied if another suitable topcoat is being applied subsequently. For greater protection prime first with Teamac Zinc Phosphate Primer.

questions Bsrry Tindall on 2018-03-21 15:05:18
Question: 

Can this paint be used on wood please? Barry

Answer from Rawlins’ Technical Team: 

Teamac Duracote Red Oxide Paint is not designed for application to wood but could be applied if necessary. We would however recommend the use of Teamac Metalastic Metal Protective Paint Colours instead where possible.

  

Question about the product

* Required fields
(read)
Send

IMPORTANT SHIPPING & DELIVERY INFORMATION

Teamac Duracote Red Oxide Paint is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


COVERAGE CALCULATOR
Units
DFT
Total area²
Or enter length and width dimensions:
Length
Width

*All estimates are based on theoretical consumption rates and do not take into account any substrate deviations or wastage

You might also like

Teamac Thinner 14

A specially formulated blend of solvents designed to mix with its compatible Teamac or Coo-Var coating to create an optimal consistancy for application. Suitable for use with Brush, Roller or Spray. Teamac Thinner 14 can also be used for the cleaning of some surfaces prior to application of the coating. Also suitable for the cleaning of...

Price £10.61 (ex. VAT)
In Stock and Available for Delivery

Coo-Var Universal Degreaser Cleaner

Coo-Var Universal Degreaser Cleaner is a careful blend of solvents to give powerful cleaning and degreasing properties. Product Features Degreases and removes oil patches from floors, walls, interior and exterior surfaces prior to acid etching or painting. Part of the cleaning process. Essential for a good finish. Can also be used as a...

Price £20.47 (ex. VAT)
In Stock and Available for Delivery

General Painting Application Kit

General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site. Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...

Price £8.02 (ex. VAT)
In Stock and Available for Delivery

Teamac Zinc Phosphate Primer

Teamac Zinc Phosphate Primer, an anticorrosive primer on iron and steel, for use with a range of conventional topcoats such as Teamac Marine Gloss and Teamac Metalcote Plant Enamel. Can be used for: Marine purposes Fire escapes Metal gates Metal garage doors Ideal in coastal areas Click to jump down to Technical Data Coverage...

Price £14.83 (ex. VAT)
In Stock and Available for Delivery