Teamac Aluminium Wood Primer, is an oil based primer that contains aluminium. Used primarily to prevent staining on knotted or resinous timber, but also acts as an excellent heavy duty primer.
Suitable for Narrowboats, Cruisers, Barges, Yachts and other Marine Applications. It can be applied to suitably prepared timbers and boards. Marine Aluminium Primer should be used as a system with Teamac Marine Primer Undercoat and Teamac Marine Gloss to retain a long lasting, high gloss finish.
Stain resistant primer ideal for resinous timber.
Provides Flat, Blister Resistant Finish for Topcoats to adhere to.
Teamac Aluminium Wood Primer, is an oil based primer that contains aluminium. Used primarily to prevent staining on knotted or resinous timber, but also acts as an excellent heavy duty primer.
Suitable for Narrowboats, Cruisers, Barges, Yachts and other Marine Applications. It can be applied to suitably prepared timbers and boards. Marine Aluminium Primer should be used as a system with Teamac Marine Primer Undercoat and Teamac Marine Gloss to retain a long lasting, high gloss finish.
Provides Flat, Blister Resistant Finish for Topcoats to adhere to.
Perfect for all timbers.
Product Specification
Technical Data
Volume Solids
45%
VOC Content
427 g/litre
SG
1.26 @ 20°C
Viscostity
3 @ 25°C
Flash Point
Above 23°C (closed cup)
Film Thickness Range And Coverage
Product Data
Dry Film Thickness
Wet Film Thickness
Theoretical Coverage
Maximum
35 to 40 μm
80 μm
12 m2/litre @ 35 micron D.F.T.
The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.
Drying Times
Drying Times At 20°C/RH 50%
Touch Dry:
2 Hours
Dry To Handle:
8 Hours
Dry To Recoat:
16 hours or overnight
Fully Cured:
N/A
Low temperature and high humidity will adversely affect application, drying and performance of any coating.
Surface Preparation
All surfaces should be clean, dry, sound and free from contaminants.
New wood should be sanded prior to coating to ensure an adequate "key" is produced.
Preceeding Coat
Apply Coo-Var Aluminium Wood Primer direct to wood.
Subsequent Coat
Most conventional, white spirit based top coats.
Mixing
Mix well before use.
Application Conditions
As dictated by normal good painting practice.
In confined spaces, provide adequate ventilation during application and drying.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
A specially formulated blend of solvents designed to mix with its compatible Teamac or Coo-Var coating to create an optimal consistancy for application.
Suitable for use with Brush, Roller or Spray.
Teamac Thinner 14 can also be used for the cleaning of some surfaces prior to application of the coating.
Also suitable for the cleaning of...
Teamac Marine Undercoat, is an interior and exterior, oil based marine undercoat. It is a high opacity undercoat with good flow characteristics for use with Teamac Marine Gloss. It has been designed to reduce topcoat sinkage and to retain a high gloss finish.
Primes and prepares - easy to use
Protects and enhances – anti-corrosive &...
Teamac Marine Gloss is a high quality, modified long oil alkyd marine coating. It has excellent gloss and opacity.
High gloss
Excellent opacity and adhesion
Touch dry in as little as 4 hours (at 20°C)
Full hardness in 5 - 7 days
Suitable for all general marine areas, bridge fonts, deck work, masts, superstructures etc
Available in...
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.
Provides an economical way of making sure you will have what you need
Ideal for interior and exterior paint projects
Click to jump down to...
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
Colourmatch Service Disclaimer
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage