PPG PhenGuard Subsea 780

    7580
    PPG3913

    PPG PhenGuard Subsea 780 (also known as Subsea 780 and Sigmaline 780) is a two-component, amine adduct-cured phenolic epoxy finish, used for the protection of subsea equipment.

    • Qualified for NORSOK M501 Rev.6 System 7C up to 150°C (302°F) with 3 coating system (Phenguard 930 / 935 / Phenguard Subsea 780 system)
    • Qualified for NORSOK M501 Rev.6 System 7C up to 180°C (356°F) with 2 coating system (Phenguard Subsea 610 Primer)

    Colour
    Size
    Finish
    £188.71(ex. VAT)
    £226.45 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    PPG PhenGuard Subsea 780 (also known as Subsea 780 and Sigmaline 780) is a two-component, amine adduct-cured phenolic epoxy finish, used for the protection of subsea equipment. Available in bright colours to assist locating by ROV, the coating has excellent resistance to seawater and high-temperatures when immersed, controlling corrosion.

    Top Features & Benefits


    • Meets the requirements of Norsok M-501 rev. 6, system 7: Qualified for NORSOK M501 Rev.6 System 7C up to 150°C (302°F) with 3 coating system (Phenguard 930 / 935 / Phenguard Subsea 780 system). Qualified for NORSOK M501 Rev.6 System 7C up to 180°C (356°F) with 2 coating system (Phenguard Subsea 610 Primer)
    • Bright colour to assist location by ROV
    • Excellent resistance to seawater immersion
    • Very good corrosion control
    • Excellent high-temperature resistance in immersed conditions
    • Good application properties, resulting in a smooth surface
    • 4 hours pot life at 20°C (68°F)
    • Available in 3 colours (Golden Yellow (RAL 1004), Pure Orange (RAL 2004), Zinc Yellow (RAL 1018)), with other colours available on request. Contact our sales team on 0113 2455450 for more information.

    Product Data


    Basic data at 20°C (68°F)

    Data for Mixed Product
    Mass density1.7 kg/l (14.2 lb/US gal)
    Volume solids66 ± 2%
    VOC (Supplied)EPA Method 24: 300.0 g/ltr (2.5 lb/USgal)
    Recommended dry film thickness100 - 175 µm (4.0 - 7.0 mils) depending on system
    Theoretical spreading rate6.6 m²/l for 100 µm (265 ft²/US gal for 4.0 mils)
    3.8 m²/l for 175 µm (151 ft²/US gal for 7.0 mils)
    Overcoating IntervalMinimum: 3 hours
    Maximum: 21 days
    Dry to touch2 hours
    Full CureSee Cure table further below

    Notes:

    • Refer to tables below for information regarding spreading rate and film thickness, overcoating intervals and curing times

    Preparation & Application


    Recommended Substrate Conditions & Temperatures


    Substrate conditions

    • Previous coat of approved coating must be dry and free from any contamination
    • Substrate must be dry, free from oil, grease and any contamination

     

    Substrate Temperature & Application Conditions


    • Substrate temperature during application and curing should be above 10°C (50°F)
    • Substrate temperature during application should be at least 3°C (5°F) above dew point

     

    Instructions For Use


    Mixing ratio by volume: base to hardener 88:12

    • The temperature of the paint should preferably be above 15°C (59°F), otherwise extra thinner may be required to obtain application viscosity
    • Adding too much thinner results in reduced sag resistance and slower cure
    • Thinner should be added after mixing the components

     

    Induction time

    Mixed product induction time
    Mixed product temperatureInduction time
    15°C (59°F)20 minutes
    20°C (68°F)15 minutes
    30°C (86°F)10 minutes

     

    Application


     

    Air spray


    Recommended Thinner

    Volume of thinner

    • 2 - 10%, depending on required thickness and application conditions

    Nozzle orifice

    • 2.0 mm (approx. 0.079 in)

    Nozzle pressure

    • 0.3 MPa (approx. 3 Bar; 44 p.s.i.)

     

    Airless spray


    Recommended Thinner

    Volume of thinner

    • 2 - 10%, depending on required thickness and application conditions

    Nozzle orifice

    • Approx. 0.46 – 0.53 mm (0.018 – 0.021 in)

    Nozzle pressure

    • 15.0 MPa (approx. 150 bar; 2176 p.s.i.)

     

    Cleaning solvent


    Additional Data


    Spreading rate and film thickness
    DFTTheoretical spreading rate
    100 µm (4.0 mils)6.6 m²/l (265 ft²/US gal)
    125 µm (5.0 mils)5.3 m²/l (212 ft²/US gal)
    175 µm (7.0 mils)3.8 m²/l (151 ft²/US gal)

     

    Overcoating interval for DFT up to 175 µm (7.0 mils)
    Overcoating with...Interval10°C (50°F)15°C (59°F)20°C (68°F)30°C (86°F)40°C (104°F)
    itselfMinimum16 hours6 hours3 hours3 hours2 hours
    Maximum28 days25 days21 days14 days7 days

    Notes:

    • Surface should be dry and free from any contamination
    • When needs to walk on for topcoat, min. recoat time should be same as dry to handle time to avoid damage on coated system

     

    Curing time for DFT up to 175 µm (7.0 mils)
    Substrate temperatureDry to handleFull cure
    10°C (50°F)16 hours5 days
    15°C (59°F)12 hours4 days
    20°C (68°F)8 hours3 days
    30°C (86°F)6 hours48 hours

     

    Note:

    • Adequate ventilation must be maintained during application and curing (please refer to INFORMATION SHEETS 1433 and 1434)

     

    Pot life (at application viscosity)
    Mixed product temperaturePot life
    10°C (50°F)6 hours
    20°C (68°F)4 hours
    30°C (86°F)1.5 hours
    40°C (104°F)30 minutes

     

    Safety Precautions

    This is a solvent-borne paint and care should be taken to avoid inhalation of spray mist or vapour, as well as contact between the wet paint and exposed skin or eyes

    Product Details
    3913-494280

    Data sheet

    Manufacturer
    PPG
    Application Method
    Spray
    Sheen
    Eggshell
    Colour
    Standard / Ready Mixed
    Single, Two or Three Pack
    Two-Pack
    Pack Size
    4L
    Parts
    Two
    Base Type
    Amine Adduct-Cured Phenolic Epoxy
    Solvent
    Solvent Based
    Mixing Ratio
    88:12
    Suitable Substrates
    Subsea metal equipment (steel)
    Key Features
    For the protection of sub-sea equipment
    Application
    Spray
    Touch Dry (at 20°C)
    2 hours
    Dry to Handle (at 20°C)
    8 hours
    Dry to Recoat (at 20°C)
    3 hours
    Fully Cured (at 20°C)
    3 days
    Pot Life (at 20°C)
    4 hours
    Coverage
    6.6 m²/l for 100 µm
    Recommended Thinner/Cleaner
    Thinner 91-92 / Thinner 90-53
    Unit Contents
    -
    Compatible Primers
    -
    Compatible Topcoats
    Itself
    Max. Application Temperature
    -
    Min. Application Temperature
    3°C above dew point
    Density
    1.7 kg/l (14.2 lb)
    Solids by Volume
    66 ± 2%
    Heat Resistance (up-to)
    -
    VOC
    EPA Method 24: 300.0 g/ltr (2.5 lb/USgal)
    Shelf Life (Once Opened)
    Base and Hardener: at least 24 months when stored cool and dry
    Touch Dry
    2 hours
    UN Number (Activator)
    UN3470
    UN Number (Base)
    UN1263
    Base Type
    Amine Adduct-Cured Phenolic
    Base Type
    Epoxy
    Finish
    Eggshell
    Application Method
    Spray
    Product Usage Type
    Topcoat
    Product Range
    PhenGuard
    Colour Family
    Yellow
    Colour Family
    Orange
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    PPG PhenGuard Subsea 780 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    PPG Thinner 90-53

    This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info

    Price £35.18 (ex. VAT)
    In Stock and Available for Delivery

    PPG Thinner 91-92

    This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info

    Price £36.75 (ex. VAT)
    In Stock and Available for Delivery