HMG Marine Varnish

    TOPMARCLE
    HMG4385

    HMG Marine Varnish is a tough and durable clear gloss formulated on a unique blend of polyurethane alkyds for high quality marine and can be used for industrial finishing.

    This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener/thinner:

    2-Pack System Details
    Base (Part 1)HMG Marine Varnish
    Thinner (Part 2)HMG Thinner 2612

    • Part one of a two-pack system
    • Available as a clear

    Colour
    Size
    Finish
    £87.14(ex. VAT)
    £104.57 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    HMG Marine Varnish is a tough and durable clear gloss formulated on a unique blend of polyurethane alkyds for high quality marine and can be used for industrial finishing.

    Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Thinner 2612.



    Click To Jump To Section:




    Features & Benefits


    • Part one of a two pack system
    • Available as a clear



    Product Specification


    Technical Data
    Volume Solids:52.4%
    VOC Content:0.460kgs/ltr
    SG:-
    Viscosity:260 mPas
    Density:0.909 g/cm³
    Storage Conditions:Store between 5°C - 25°C. When not in use, cans must be kept sealed.
    Shelf Life:12 months from delivery date in original sealed containers.
    Flash Point:>30°C



    Film Thickness Range And Coverage


    Product Data
     Dry Film ThicknessWet Film Thickness
    Brush:n/an/a
    Compliant Spray Gun:n/an/a



    Coverage: 18.4 square metres per litre @25 microns dft (Theoretical)

    • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
    • These values are a guide only and are not to be used as specifications.
    • Film thickness will vary depending on actual use and specification.
    • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



    Drying Times


    Drying Times At 20°C
    Touch Dry:5 minutes
    Dry To Handle:20 minutes
    Dry To Recoat:At any stage of dry.
    Fully Cured:1 hour



    Surface Preparation


    • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.



    Application Methods


    Technical Data
    HVLPCompliant Spray Gun
    Mixing Ratio:Base: 9.5Base: 9
    Thinner: 0.5 approxThinner: 1 approx
    Thinner Options:Thinner 2612Thinner 2612
    --
    Viscosity:--
    Spray Gun Setup:-1.4 - 1.6
    Number Of Coats (Guide Only):2 - 3 full coats2 - 3 full coats
    Flash Off:15 minutes between coats15 minutes between coats



    For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



    Product Notes


    Information on basic physical and chemical properties
    Form:Liquid
    Colour:According to product specification
    Odour:Characteristic
    Odour Threshold:Not determined
    pH-value:Not determined
    Change in Condition
    Melting point/freezing point:Undetermined
    Initial boiling point and boiling range:135°C
    Flash Point:>30°C
    Flammability (solid, gas):Not applicable
    Ignition temperature:>200°C
    Decomposition temperature:Not determined.
    Auto-ignition temperature:Product is not selfigniting
    Explosive properties:"Product is not explosive. However, formation of explosive air vapour mixtures are possible."
    Explosion limits: Lower:0.6 Vol %
    Explosion limits: Upper:7 Vol %
    Vapour pressure at 20°C:2 hPa
    Density at 20°C:0.909 g/cm³
    Relative density:Not determined
    Vapour density:Not determined
    Evaporation rate:Not determined
    Solubility in / Miscibility with water:NOT MISCIBLE
    Partition coefficient: n-octanol/water:Not determined
    Viscosity: Dynamic at 20°C:260 mPas
    Viscosity: Kinematic:Not determined
    Solvent content: Organic solvents:46.5%
    Solids content:52.4%



    Health & Safety


    • Refer to the safety data sheet in the attachments section above and tin label prior to use.
    • Suitable respiratory equipment should be worn when spraying.

    Click to go back to the top of the page

    Product Details
    4385-637379

    Data sheet

    Manufacturer
    HMG Paints Limited
    Application Method
    Brush, Spray
    Sheen
    Gloss
    Colour
    Clear
    Single, Two or Three Pack
    Two-Pack
    Pack Size
    5L
    Mixing Ratio
    Compliant Spray Gun - Base: 9/Thinner: 1 approx
    Mixing Ratio
    HVLP - Base: 9.5/Thinner: 0.5 approx
    Touch Dry (at 20°C)
    5 Minutes
    Dry to Handle (at 20°C)
    20 Minutes
    Dry to Recoat (at 20°C)
    At any stage of dry
    Fully Cured (at 20°C)
    1 Hour
    Coverage
    18.4 square metres per litre @25 microns dft
    Density
    0.909 g/cm³
    Solids by Volume
    52.4 %
    VOC
    0.460kgs/ltr
    VOC
    0.460kgs/ltr
    Shelf Life (from date of manufacture)
    12 months from delivery date in original sealed containers
    UN Number
    1263
    Base Type
    Polyurethane
    Base Type
    Alkyd
    Finish
    Gloss
    Application Method
    Brush
    Application Method
    Spray
    Product Usage Type
    Topcoat
    Colour Family
    Clear
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    HMG Marine Varnish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    HMG Thinner 2612

    HMG Thinner 2612 is a slow thinner.For use with compatible HMG systems.More Information Delivery Info

    Price £11.22 (ex. VAT)
    In Stock and Available for Delivery