PPG Thinner 90-53
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£42.59 (incl. VAT)
£35.49 (ex. VAT)
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
PPG AquaCover 80 is a fast-drying, waterborne, high-build acrylic coating for steel that applies in a single coat and can be overcoated with dispersion paints.
Technical Data | ||||||
---|---|---|---|---|---|---|
PPG AquaCover 80 | ||||||
Number of Components: | One | |||||
Mass Density: | 1.2 kg/l (10.0 lb/US gal) | |||||
Volume Solids: | 45 ± 2% | |||||
VOC (supplied): | Directive 1999/13/EC, SED: max. 29.0 g/kg) | |||||
max. 35.0 g/l (approx. 0.3 lb/US gal) | ||||||
Recommended Dry Film Thickness: | 150 - 300 µm (6.0 - 12.0 mils) per coat | |||||
Theoretical Spreading Rate: | 3.0 m²/l for 150 µm (120 ft²/US gal for 6.0 mils) | |||||
1.5 m²/l for 300 µm (60 ft²/US gal for 12.0 mils) | ||||||
Shelf Life: | At least 18 months when stored cool and dry |
Curing time for DFT up to 150 µm (6.0 mils) | |||
---|---|---|---|
Substrate temperature | Dry To Touch | Dry To Handle | |
10°C (50°F) | 1.5 hours | 2.5 hours | |
20°C (68°F) | 1 hour | 2 hours | |
30°C (86°F) | 45 minutes | 1.5 hours | |
40°C (104°F) | 30 minutes | 1 hour |
Overcoating interval for DFT up to 150 µm (6.0 mils) | |||||
---|---|---|---|---|---|
Overcoating with: | Interval | 10°C (50°F) | 20°C (68°F) | 30°C (86°F) | 40°C (104°F) |
Itself and waterborne finishes | |||||
Minimum | 6 hours | 4 hours | 3 hours | 2 hours | |
Maximum | Unlimited | Unlimited | Unlimited | Unlimited |
Substrate Conditions
Substrate Temperature & Application Conditions
Instructions For Use
Airless Spray:
Brush/Roller:
Volume Of Thinner
Cleaning Solvent
Cleaning Procedures
Table 1: Cleaning procedure from solvent-borne to waterborne paints | |
---|---|
Steps | Cleaning Text |
1st cleaning | THINNER 90-53 |
2nd cleaning | THINNER 40-25, THINNER 70-05 or THINNER 70-04 |
3rd cleaning | With warm tap water of 30°C (86°F) to 35°C (95°F) after which waterborne paints can be sprayed |
Table 2: Cleaning procedure from waterborne to solvent-borne paints | |
---|---|
Steps | Cleaning Text |
1st cleaning | Warm tap water of 30°C (86°F) to 35°C (95°F) |
2nd cleaning | THINNER 40-25, THINNER 70-05 or THINNER 70-04 |
3rd cleaning | THINNER 90-53 |
Information On Basic Physical And Chemical Properties | ||||||
---|---|---|---|---|---|---|
PPG AquaCover 80 | ||||||
Form: | Liquid | |||||
Colour: | Various | |||||
Odour: | Amine-like | |||||
Odour Threshold: | Not available | |||||
pH-value 20°C: | Not available | |||||
Melting point/freezing point: | May start to solidify at the following temperature: 0°C (32°F) This is based on data for the following ingredient: water. Weighted average: -8.37°C (16.9°F) | |||||
Initial boiling point and boiling range: | >37.78°C | |||||
Flash Point: | Closed cup: Not applicable | |||||
Evaporation Rate: | 0.003 (2-(2-butoxyethoxy)ethanol) compared with butyl acetate | |||||
Flammability (solid, gas): | liquid | |||||
Upper/lower flammability or : explosive limits: | Greatest known range: Lower: 0.8% Upper: 9.4% (2-(2-butoxyethoxy)ethanol) | |||||
Vapour pressure: | Highest known value: 3.2 kPa (23.8 mm Hg) (at 20°C) (water). Weighted average: 2.78 kPa (20.85 mm Hg) (at 20°C) | |||||
Vapour Density: | Highest known value: 7.5 (Air = 1) (isobutyric acid, monoester with 2,2,4-trimethylpentane-1,3-diol). Weighted average: 6.73 (Air = 1) | |||||
Relative density: | 1.27 | |||||
Solubility(ies): | Partially soluble in the following materials: cold water | |||||
Partition coefficient: n-octanol/ water: | Not applicable | |||||
Auto-ignition temperature: | Lowest known value: 210°C (410°F) (2-(2-butoxyethoxy)ethanol) | |||||
Decomposition temperature: | Stable under recommended storage and handling conditions | |||||
Viscosity: | Kinematic (40°C): >0.21 cm² /s 60 - 100 s (ISO 6mm) | |||||
Explosive properties: | The product itself is not explosive, but the formation of an explosible mixture of vapour or dust with air is possible. | |||||
Oxidising properties: | Product does not present an oxidizing hazard |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
PPG AquaCover 80 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£42.59 (incl. VAT)
£35.49 (ex. VAT)