- There are no more items in your cart
- Shipping Calculated at checkout
- Sub-Total(ex. VAT)(inc. VAT)£0.00£0.00
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
International Intercryl 507 a water based, acrylic finish for use on internal accommodation areas, storerooms etc.
- Low odour
- Good gloss retention
- Easy clean
- Non-yellowing properties
- Part of a specified, approved, fire retardant scheme
- For use at newbuilding or maintenance & repair
Description
International Intercryl 507 a water based, acrylic finish for use on internal accommodation areas, storerooms etc.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Product Details
- Drying Times
- Surface Preparation
- Application Conditions
- Applications
- Limitations
- Health and Safety
Features & Benefits
- Low odour
- Good gloss retention
- Easy clean
- Non-yellowing properties
- Part of a specified, approved, fire retardant scheme
- For use at newbuilding or maintenance & repair
Product Details
| Technial Data | |
|---|---|
| Volume Solids: | 40% ±2% (ISO 3233:1998) |
| Typical Film Thickness: | 50 microns dry (125 microns wet). Range 30 - 60 microns dry (75 - 150 microns wet) may be specified depending upon end use and method of application. |
| Theoretical Coverage: | 8.00 m²/litre at 50 microns dft, allow appropriate loss factors |
| VOC: | 135 g/lt |
| Shelf Life: | 12 months minimum at 25°C |
Drying Times
| Drying Information | ||||
|---|---|---|---|---|
| 5°C | 10°C | 25°C | 35°C | |
| Touch Dry | 120 minutes | 100 minutes | 60 minutes | 30 minutes |
| Hard Dry | 16 hours | 12 hours | 4 hours | 4 hours |
| Overcoating Data | ||||||||
|---|---|---|---|---|---|---|---|---|
| 5°C | 10°C | 25°C | 35°C | |||||
| Overcoated By | Min | Max | Min | Max | Min | Max | Min | Max |
| Intercryl 507 | 16 hours | Ext | 14 hours | Ext | 8 hours | Ext | 4 hours | Ext |
Surface Preparation
- Use in accordance with the standard Worldwide Marine Specifications
- All surfaces to be coated should be clean, dry and free from contamination
- High pressure freshwater wash or freshwater wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning
Newbuilding
- Intercryl 507 should be applied over Intercryl 506, the surface of which should be dry and free of all contaminants
- Intercryl 507 must be applied within the overcoating intervals specified on the Intercryl 506 data sheet
Major Refurbishment
- Intercryl 507 should be applied over Intercryl 506, the surface of which should be dry and free of all contaminants
- Intercryl 507 must be applied within the overcoating intervals specified on the Intercryl 506 data sheet
Repair
- Repair corroded/damaged areas with recommended anticorrosive primer
- Apply Intercryl 507 within the overcoating intervals specified (consult primer data sheet)
Consult Rawlins Technical Team on 0113 2455450 (option 2) or [email protected] for specific recommendations.
Application Conditions
- This product should not be exposed to temperatures of 0°C or below (protect from frost)
- Do not apply at temperatures below 5°C
- Rate of drying is humidity and airflow dependant
- Do not apply when relative humidity exceeds 85%
Application
Mixing
This material is a one pack coating and should always be mixed thoroughly with a power agitator before application
Mix Ratio
- Not applicable
| Application Methods | |||
|---|---|---|---|
| Airless Spray | Recommended | Tip Range 0.33-0.43 mm (13-17 thou) Total output fluid pressure at spray tip not less than 211 kg/cm² (3000 p.s.i.) | |
| Conventional Spray | Suitable | Use suitable proprietary equipment. Thinning may be required | |
| Brush | Suitable | ||
| Roller | Suitable | ||
| Thinner | Not recommended | ||
| Cleaner | Water/detergent | ||
Work Stoppages and Clean Up
- Thoroughly flush all equipment with water/detergent
- All unused material should be stored in tightly closed containers
- Partially filled containers may show surface skinning and/or viscosity increase of the material after storage
- Material should be filtered prior to use
Welding
- In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation
Limitations
- Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions
- Consult Rawlins Technical Team on 0113 2455450 (option 2) or [email protected] representative for specific recommendations
- Apply in good weather
- Temperature of the surface to be coated must be at least 3°C above the dew point
- For optimum application properties bring the material to 21-27°C, unless specifically instructed otherwise, prior to mixing and application
- Unmixed material (in closed containers) should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet
- Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures
- Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments
- As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating
Health and Safety
- Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards
- Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.)
- Actual safety measures are dependent on application methods and work environment
- Please refer to the product data sheet and safety data sheet in the attachents section above
Product Details
WXE000/20LT
Data sheet
- Manufacturer
- International
- Interior / Exterior Use
- Interior
- Water / Solvent Based
- Water
- Application Method
- Brush, Roller, Spray
- Sheen
- Gloss
- Colour
- Standard / Ready Mixed
- VOC Levels
- Low (50-149 g/l)
- Single, Two or Three Pack
- Single
- Pack Size
- 20L
- Coverage
- 8.00 m²/litre at 50 microns dft
- Recommended Thinner/Cleaner
- Cleaner: Water/detergent
- Min. Application Temperature
- 5°C
- Solids by Volume
- 40% ±2%
- VOC
- 135 g/lt
- Shelf Life (from date of manufacture)
- 12 months minimum at 25°C
- Touch Dry
- 5°C: 120 minutes, 10°C: 100 minutes, 25°C: 60 minutes, 35°C: 30 minutes
- Recommended Dry Film Thickness
- 50 microns
- Recommended Wet Film Thickness
- 125 microns
- Hard Dry
- 5°C: 16 hours, 10°C: 12 hours, 25°C: 4 hours, 35°C: 4 hours
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
International Intercryl 507 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT