HMG Acrythane XSC98 11

    TOPXSC98/11
    HMG4405

    HMG Acrythane XSC98 11 (Base) is an ultra high solids (UHS) compliant coating. It is 2K acrylic cured with an isocyanate hardener with outstanding properties.

    This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:

    2-Pack System Details
    Base (Part 1)HMG Acrythane XSC98 11
    Activator (Part 2)HMG Hardener 9039

    • Part one of a two part system
    • Rapid drying, even at low temperatures
    • High gloss
    • Simplicity of use
    • Available in 3,500+ colours, inc. RAL, Metallics, BS, NCS & the new NCS 2050 colours
    • Excellent protection against harsh weather conditions, atmospheric pollution, road dirt, sharp cleaning agents, mechanical car washes and most industrial chemicals.

    Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

    Product customisation

    Don't forget to save your customization to be able to add to cart
    • 250 char. max
    Colour Group
    Size
    Finish
    £29.28(ex. VAT)
    £35.14 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    HMG Acrythane XSC98 11 is an ultra high solids (UHS) compliant coating. It is 2K acrylic cured with an isocyanate hardener with outstanding properties.

    Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Hardener 9039



    Click To Jump To Section:




    Features & Benefits


    • Rapid drying, even at low temperatures
    • High gloss
    • Simplicity of use
    • Excellent protection against harsh weather conditions, atmospheric pollution, road dirt, sharp cleaning agents, mechanical car washes and most industrial chemicals.



    Product Specification


    Technical Data
     HMG Acrythane XSC98 11 ClearcoatHMG Acrythane XSC98 11 ColourHMG Acrythane XSC98 11 Black
    Volume Solids:49.9%58.8%58.0%
    VOC Content:0.420 Kg/l0.420 Kg/l0.420 Kg/l
    SG:---
    Viscosity:140 mPas300 mPas200 mPas
    Density:0.99 g/cm³1.111 g/cm³1.019 g/cm³
    Storage Conditions:Store between 5°C - 25°C. When not in use, cans must be kept sealed.Store between 5°C - 25°C. When not in use, cans must be kept sealed.Store between 5°C - 25°C. When not in use, cans must be kept sealed.
    Shelf Life:12 months from delivery date in original sealed containers.12 months from delivery date in original sealed containers.12 months from delivery date in original sealed containers.
    Pot Life:1 Hour @ 20°C1 Hour @ 20°C1 Hour @ 20°C
    Flash Point:25°C25°C25°C



    Film Thickness Range And Coverage


    Product Data
     Dry Film ThicknessWet Film Thickness
    Compliant Spray Gun:50 μm80 μm
    Pressure Pot:50 μm80 μm



    Coverage: 11 square metres per litre @ 50 microns dft.

    • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
    • These values are a guide only and are not to be used as specifications.
    • Film thickness will vary depending on actual use and specification.
    • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



    Drying Times


    Drying Times At 20°C
    Touch Dry:1 hour
    Dry To Handle:16 hours
    Dry To Recoat:Flat with 500's after hard dry. Spreading rate 12 sq/m² per litre mixed (Average)
    Fully Cured:3 - 5 days



    Surface Preparation


    • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
    • Read and follow safety data sheet, product data sheet and label instructions.
    • Stir all paints thoroughly before use.
    • Always use the same batch number on the same job.
    • Check colour & sheen.
    • Filter the product immediately before use.
    • Reduce emissions and maintain quality by replacing tin lid after use.



    Application Methods


    Technical Data
    Compliant Spray GunPressure Pot
    Mixing Ratio:Base: 2Base: 2
    Hardener: 1Hardener: 1
    Thinner: 0.5Thinner: 0.5
    Hardener Options:Hardener 9039Hardener 9039
    Thinner Options:Thinner 2601Thinner 2601
    Thinner 2602Thinner 2602
    Thinner 2603Thinner 2603
    Thinner 2604Thinner 2604
    Viscosity:21 - 26 seconds B4 cup21 - 26 seconds B4 cup
    Spray Gun Setup:1.6 - 1.81.1 - 1.4
    Number Of Coats (Guide Only):1 medium + 1 full1 medium + 1 full
    Flash Off:15 minutes between coats15 minutes between coats



    For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



    Product Notes


    Information On Basic Physical And Chemical Properties
     HMG Acrythane XSC98 11 ClearcoatHMG Acrythane XSC98 11 ColourHMG Acrythane XSC98 11 Black
    Form:LiquidLiquidLiquid
    Colour:ClearAccording to product specificationBlack
    Odour:CharacteristicCharacteristicCharacteristic
    Odour Threshold:Not determinedNot determinedNot determined
    pH-value 20°C:Not determinedNot determinedNot determined
    Melting point/freezing point:UndeterminedUndeterminedUndetermined
    Initial boiling point and boiling range:126°C126°C124°C
    Flash Point:25°C25°C25°C
    Flammability (solid, gas):Not applicableNot applicableNot applicable
    Ignition temperature:315°C415°C415°C
    Decomposition temperature:Not determined.Not determined.Not determined.
    Auto-ignition temperature:Product is not selfignitingProduct is not selfignitingProduct is not selfigniting
    Explosive properties:"Product is not explosive. However, formation of explosive air vapour mixtures are possible.""Product is not explosive. However, formation of explosive air vapour mixtures are possible.""Product is not explosive. However, formation of explosive air vapour mixtures are possible."
    Explosion limits: Lower:3.0 Vol %1.2 Vol %1.1 Vol %
    Explosion limits: Upper:10.4 Vol %7.5 Vol %7.5 Vol %
    Vapour pressure at 20°C:10.7 hPa11.2 hPa11.2 hPa
    Density at 20°C:0.99 g/cm³1.111 g/cm³1.019 g/cm³
    Relative density:Not determinedNot determinedNot determined
    Vapour density:Not determinedNot determinedNot determined
    Evaporation rate:Not determinedNot determinedNot determined
    Solubility in / Miscibility with water:NOT MISCIBLENOT MISCIBLENOT MISCIBLE
    Partition coefficient: n-octanol/water:Not determinedNot determinedNot determined
    Viscosity: Dynamic at 20°C:140 mPas300 mPas200 mPas
    Viscosity: Kinematic:Not determinedNot determinedNot determined
    Solvent content: Organic solvents:45.5%37.9%37.4%
    Solids content:49.9%58.8%58.0%



    Health & Safety


    • Refer to the safety data sheet in the attachments section above and tin label prior to use.
    • Ready for use product contains isocyanates. Suitable air fed respiratory equipment should be worn when spraying.

    Click to go back to the top of the page

    Product Details
    4405-851961

    Data sheet

    Manufacturer
    HMG Paints Limited
    For Use On
    Metal
    Application Method
    Spray
    Sheen
    Gloss
    Colour
    Fully Tintable
    Single, Two or Three Pack
    Two-Pack
    Pack Size
    1L
    5L
    Mixing Ratio
    Base: 2 - Hardener: 1 - Thinner: 0.5
    Application
    Spray
    Touch Dry (at 20°C)
    60 mins
    Dry to Handle (at 20°C)
    16 Hours
    Dry to Recoat (at 20°C)
    Flat with 500's after Hard Dry. Spreading rate 12 sq/m2 per litre mixed (Average)
    Fully Cured (at 20°C)
    3 - 5 Days
    Pot Life (at 20°C)
    1 Hour
    Recommended Thinner/Cleaner
    Thinner 2601/2602/2603/2604
    Compatible Primers
    Polykote 2K AMC4 Primer
    Density
    Clearcoat: 0.99 g/cm³ - Colour: 1.111 g/cm³ - Black: 1.019 g/cm³
    Solids by Volume
    Clearcoat: 49.9 % - Colour: 58.8 % - Black: 58.0 %
    Heat Resistance (up-to)
    120 °C
    VOC
    0.420 Kg/l
    Shelf Life (from date of manufacture)
    12 months from delivery date in original sealed containers.
    Finish
    Gloss
    Size
    1L, 2.5L, 5L
    Recommended Dry Film Thickness
    50 μm
    Recommended Wet Film Thickness
    80 μm
    UN Number
    UN1263
    Base Type
    Solvent-Based
    Suitable For Use On
    Primed Surfaces
    Finish
    Matt
    Finish
    High Gloss
    Finish
    Satin
    Application Method
    Spray
    Usages
    Tough/Durable
    Usages
    Atmospheric Polution Resistance
    Usages
    High Solids
    Usages
    Atmospheric
    Usages
    Weather Resistance
    Usages
    Chemical Resistance
    Product Usage Type
    Topcoat
    Product Range
    Acrythane
    Colour Family
    Grey
    Colour Family
    Black
    Colour Family
    Blue
    Colour Family
    White
    Colour Family
    Brown
    Colour Family
    Metallic
    Colour Family
    Orange
    Colour Family
    Beige
    Colour Family
    Yellow
    Colour Family
    Green
    Colour Family
    Clear
    Colour Family
    Red
    Colour Family
    Neutral
    Colour Family
    Pink
    Colour Family
    Stone
    Colour Family
    Anthracite Grey
    Colour Family
    Purple
    Product Type
    Epoxy
    Environment
    Atmospheric
    Touch Dry/Dust Free (@ 20-25°C)
    60 mins
    Resistance to
    Chemicals
    Resistance to
    Weather
    Resistance to
    Atmospheric Polution
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    HMG Acrythane XSC98 11 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    HMG Thinner 2601

    HMG Thinner 2601 is a very fast thinner.For use in recommended HMG systems.More Information Delivery Info

    Price £11.22 (ex. VAT)
    In Stock and Available for Delivery

    HMG Thinner 2602

    HMG Thinner 2602 is a medium slow thinner.For use with compatible HMG systems.More Information Delivery Info

    Price £11.26 (ex. VAT)
    In Stock and Available for Delivery

    HMG Thinner 2603

    HMG Thinner 2603 is a medium slow thinner.For use with compatible HMG systems.More Information Delivery Info

    Price £38.22 (ex. VAT)
    In Stock and Available for Delivery

    HMG Thinner 2604

    HMG Thinner 2604 is a slow thinner.For use with compatible HMG systems.More Information Delivery Info

    Price £11.78 (ex. VAT)
    In Stock and Available for Delivery

    HMG 2K Accelerator

    HMG 2K Accelerator is a hardener designed to speed up drying times.For use with HMG Acrythane systems.More Information Delivery Info

    Price £31.84 (ex. VAT)
    In Stock and Available for Delivery

    HMG Hardener 9039

    HMG Hardener 9039 is a high solids isocyanate hardener. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) HMG Acrythane XSC98 11HMG Monothane 2K TopcoatActivator (Part 2) HMG Hardener 9039Part two of a two...

    Price £24.64 (ex. VAT)
    In Stock and Available for Delivery

    Surface Preparation Kits for Steel

    These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...

    Price £21.53 (ex. VAT)
    In Stock and Available for Delivery