HMG Acrythane ACE is a high performance 2K acrylic polyurethane finish designed to meet the exacting requirements of the agricultural & construction equipment markets.
This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:
| 2-Pack System Details | |||||
|---|---|---|---|---|---|
| Base (Part 1) | HMG Acrythane ACE | ||||
| Hardener (Part 2) | HMG Hardener 9014 | ||||
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
HMG Acrythane ACE is a high performance 2K acrylic polyurethane finish designed to meet the exacting requirements of the agricultural & construction equipment markets.
Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Hardener 9014.
Recommended for use in with the following HMG primer/filler/sealer systems:
| Technical Data | ||||
|---|---|---|---|---|
| Volume Solids: | 61.7% | |||
| VOC Content: | 0.42kgs/ltr | |||
| SG: | - | |||
| Viscosity: | 360 mPas | |||
| Density: | 1.159 g/cm³ | |||
| Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | |||
| Shelf Life: | 12 months from delivery date in original sealed containers. | |||
| Pot Life: | 4 Hours @ 20°C | |||
| Flash Point: | 24°C | |||
| Product Data | |||
|---|---|---|---|
| Dry Film Thickness | Wet Film Thickness | ||
| Airless/Air-Assisted: | 25 - 50 μm | 60 - 125 μm | |
| HVLP: | - | - | |
Coverage: 19.5 square metres per litre @ 25 microns dft (theoretical)
| Drying Times At 20°C | |
|---|---|
| Touch Dry: | 1 hour |
| Dry To Handle: | 8 hours |
| Fully Cured: | 7 days |
| Technical Data | |||||
|---|---|---|---|---|---|
| Airless/Air-Assisted | HVLP | ||||
| Mixing Ratio: | Base: 2 | Base: 2 | |||
| Hardener: 1 | Hardener: 1 | ||||
| Hardener Options: | Hardener 9014 | Hardener 9014 | |||
| Thinner Options: | Thinner 2604 | Thinner 2604 | |||
| Viscosity: | Ready for use | 21 - 28 seconds B4 cup | |||
| Spray Gun Setup: | 11 - 13 thou 40/50° | 1.2 - 1.6 tip | |||
| Number Of Coats (Guide Only): | 1 - 2 full coats | 1 - 2 coats | |||
| Flash Off: | 15 minutes between coats | 15 minutes between coats | |||
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
| Information On Basic Physical And Chemical Properties | ||||
|---|---|---|---|---|
| Form: | Liquid | |||
| Colour: | According to product specification | |||
| Odour: | Characteristic | |||
| Odour Threshold: | Not determined | |||
| pH-value 20°C: | Not determined | |||
| Change in Condition | ||||
| Melting point/freezing point: | Undetermined | |||
| Initial boiling point and boiling range: | 126°C | |||
| Flash Point: | 24°C | |||
| Flammability (solid, gas): | Not applicable | |||
| Ignition temperature: | 315°C | |||
| Decomposition temperature: | Not determined. | |||
| Auto-ignition temperature: | Product is not selfigniting | |||
| Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | |||
| Explosion limits: Lower: | 1.2 Vol % | |||
| Explosion limits: Upper: | 10.8 Vol % | |||
| Vapour pressure at 20°C: | 11.2 hPa | |||
| Density at 20°C: | 1.159 g/cm³ | |||
| Relative density: | Not determined | |||
| Vapour density: | Not determined | |||
| Evaporation rate: | Not determined | |||
| Solubility in / Miscibility with water: | NOT MISCIBLE | |||
| Partition coefficient: n-octanol/water: | Not determined | |||
| Viscosity: Dynamic at 20°C: | 360 mPas | |||
| Viscosity: Kinematic: | Not determined | |||
| Solvent content: Organic solvents: | 38.2% | |||
| Solids content: | 61.7% | |||
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG Acrythane ACE is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Epiprime is a zinc phosphate 2K epoxy primer offering excellent adhesion. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) HMG EpiprimeActivator (Part 2) Option 1: HMG Hardener 9058 StandardOption 2: HMG Hardener...
£23.30 (incl. VAT)
£19.42 (ex. VAT)
HMG Epoxy Primer EP2 (Base) is a zinc phosphate 2K epoxy primer offering excellent adhesion. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) HMG Epoxy Primer EP2Hardener (Part 2) HMG Hardener 9070 (Standard)HMG...
£92.96 (incl. VAT)
£77.47 (ex. VAT)
HMG Thinner 2604 is a slow thinner.For use with compatible HMG systems.More Information Delivery Info
£14.69 (incl. VAT)
£12.24 (ex. VAT)
HMG Hardener 9014 is an isocyanate hardener. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) HMG Acrythane ACEHardener (Part 2) HMG Hardener 9014Part one of a two-pack systemMore Information Delivery Info
£131.78 (incl. VAT)
£109.82 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)
