HMG Thinner 2691
HMG Thinner 2691 is a thinner for use in various applications.For use with compatible HMG systems.More Information Delivery Info
£13.21 (incl. VAT)
£11.01 (ex. VAT)
HMG Nisocoat HS (Base) is a high solid, compliant 2K non-isocyanate finish.
This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:
2-Pack System Details | |||
---|---|---|---|
Base (Part 1) | HMG Nisocoat HS | ||
Hardener (Part 2) | HMG Hardener 9097 |
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
HMG Nisocoat HS is a high solid, compliant 2K non-isocyanate finish.
Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Hardener 9097.
Technical Data | ||||
---|---|---|---|---|
Volume Solids: | 68.0% | |||
VOC Content: | 0.42kgs/ltr | |||
SG: | 1.19 | |||
Viscosity: | 300 mPas | |||
Density: | 1.4 g/cm³ | |||
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | |||
Shelf Life: | 12 months from delivery date in original sealed containers. | |||
Pot Life: | 8 hours at 20°C | |||
Flash Point: | 24°C |
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Compliant Spry Gun: | 25 - 50 μm | 50.5 - 101 μm | |
Pressure Pot: | 25 - 50 μm | 50.5 - 101 μm | |
Airless/Air-Assisted: | 25 - 50 μm | 50.5 - 101 μm |
Coverage: 16.5 square metres per litre @ 30microns assuming 100% transfer efficiency.
Drying Times At 20°C | |
---|---|
Touch Dry: | 30 minutes |
Dry To Handle: | 4 hours |
Dry To Recoat: | After 30 minutes |
Fully Cured: | 7 days |
Technical Data | |||||
---|---|---|---|---|---|
Compliant Spray Gun | Pressure Pot | Airless/Air-Assisted | |||
Mixing Ratio: | Base: 9 | Base: 9 | Base: 9 | ||
Hardener: 1 | Hardener: 1 | Hardener: 1 | |||
Thinner: 1 | Thinner: 1 | Thinner: 1 | |||
Hardener Options: | Hardener 9097 | Hardener 9097 | Hardener 9097 | ||
Thinner Options: | Thinner 2691 | Thinner 2691 | Thinner 2691 | ||
Viscosity: | - | - | - | ||
Spray Gun Setup: | 1.8mm - 2.0mm | 1.1mm - 1.4mm | 13 thou | ||
Number Of Coats (Guide Only): | 1 - 2 full coats | 1 - 2 full coats | 1 full coat | ||
Flash Off: | 10 - 15 minutes between coats | 10 - 15 minutes between coats | 10 - 15 minutes between coats |
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Information On Basic Physical And Chemical Properties | ||||
---|---|---|---|---|
Form: | Liquid | |||
Colour: | According to product specification | |||
Odour: | Characteristic | |||
Odour Threshold: | Not determined | |||
pH-value 20°C: | Not determined | |||
Change in Condition | ||||
Melting point/freezing point: | Undetermined | |||
Initial boiling point and boiling range: | 118°C | |||
Flash Point: | 24°C | |||
Flammability (solid, gas): | Not applicable | |||
Ignition temperature: | 315°C | |||
Decomposition temperature: | Not determined. | |||
Auto-ignition temperature: | Product is not selfigniting | |||
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | |||
Explosion limits: Lower: | 1.0 Vol % | |||
Explosion limits: Upper: | 7.0 Vol % | |||
Vapour pressure at 20°C: | 6.7 hPa | |||
Density at 20°C: | 1.4 g/cm³ | |||
Relative density: | Not determined | |||
Vapour density: | Not determined | |||
Evaporation rate: | Not determined | |||
Solubility in / Miscibility with water: | NOT MISCIBLE | |||
Partition coefficient: n-octanol/water: | Not determined | |||
Viscosity: Dynamic at 20°C: | 300 mPas | |||
Viscosity: Kinematic: | Not determined | |||
Solvent content: Organic solvents: | 21.0% | |||
Solids content: | 68.0% |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG Nisocoat HS is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Thinner 2691 is a thinner for use in various applications.For use with compatible HMG systems.More Information Delivery Info
£13.21 (incl. VAT)
£11.01 (ex. VAT)
HMG Hardener 9097 is a 2K polyamide hardener for use in certain HMG systems. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) HMG Nisocoat HSHardener (Part 2) HMG Hardener 9097Part two of a two part pack....
£60.96 (incl. VAT)
£50.80 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)