HMG Polykote 2K TAP Primer

    PRI2KTAP
    HMG4451

    HMG Polykote 2K TAP Primer (Base) is a transparent 2K adhesion promoter /primer / sealer. It is designed for use on sound OEM finishes when minimum sanding is required and has the additional benefit of being used as a `wet on wet` primer to optimise process times.

    This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener/thinner:

    3-Pack System Details
    Base (Part 1)HMG Polykote 2K TAP Primer
    Hardener (Part 2)HMG Hardener 9004 Standard
    HMG Hardener 9027 Wintermix
    Thinner (Part 3)HMG Thinner 2601
    HMG Thinner 2602
    HMG Thinner 2603

    • Part one of a three-pack system
    • Suitable for colour changes to new vehicles
    • Available as a clear

    Colour
    Size
    Finish
    £116.75(ex. VAT)
    £140.10 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    HMG Polykote 2K TAP Primer is a transparent 2K adhesion promoter/primer/sealer. It is designed for use on sound OEM finishes when minimum sanding is required and has the additional benefit of being used as a 'wet on wet' primer to optimise process times.

    Please note this product is one part of a three-pack system which MUST be purchased/used together with HMG Hardener 9004 Standard or HMG Hardener 9027 Wintermix. A thinner option must also be purchased from HMG Thinner 2601, HMG Thinner 2602 or HMG Thinner 2603.



    Click To Jump To Section:




    Features & Benefits


    • Suitable for colour changes to new vehicles
    • Available as a clear

    It is particularly suitable for colour changes to new vehicles as no sanding is required, however it is recommended that leading edges, such as wheelarches, front of bonnets etc, are scotchbrited for maximum performance.

    Not for use as a bare metal primer.



    Product Specification


    Technical Data
    Polykote 2K TAP Primer
    Volume Solids:49.6%
    VOC Content:0.600 Kg/l
    SG:-
    Viscosity:350 mPas
    Density:1.097 g/cm³
    Storage Conditions:Store between 5°C - 25°C. When not in use, cans must be kept sealed.
    Shelf Life:12 months from delivery date in original sealed containers.
    Pot Life:3 hours at 20°C
    Flash Point:25°C



    Film Thickness Range And Coverage


    Product Data
     Dry Film ThicknessWet Film Thickness
    Compliant Spray Gun:25 μm50 μm
    Pressure Pot:25 μm50 μm



    Coverage: 16.8 square metres per litre @ 25 microns dft mixed

    • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
    • These values are a guide only and are not to be used as specifications.
    • Film thickness will vary depending on actual use and specification.
    • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



    Drying Times


    Drying Times At 20°C
    Touch Dry:2 hours
    Dry To Recoat:Minimum of 30 minutes at 20°C, when used as a Wet on Wet. Minimum of 4 hours at 20°C when flatting.
    Fully Cured:8 hours



    Surface Preparation


    • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
    • Read and follow the safety data sheet, product data sheet and label instructions.
    • Stir all paints thoroughly before use.
    • Always use the same batch number on the same job.
    • Check colour & sheen.
    • Filter the product immediately before use.
    • Reduce emissions and maintain quality by replacing tin lid after use.



    Application Methods


    Technical Data
    Compliant Spray GunPressure Pot
    Mixing Ratio:Base: 3Base: 3
    Hardener: 1Hardener: 1
    Thinner: 1Thinner: 1
    Hardener Options:Hardener 9004 StandardHardener 9004 Standard
    Hardener 9027 WintermixHardener 9027 Wintermix
    Thinner Options:Thinner 2601Thinner 2601
    Thinner 2602Thinner 2602
    Thinner 2603Thinner 2603
    Viscosity:16 - 22 seconds B4 cup16 - 22 seconds B4 cup
    Spray Gun Setup:1.6 - 1.81.1 - 1.4
    Number Of Coats (Guide Only):1 - 2 even coats1 - 2 even coats
    Flash Off:10 - 15 minutes between coats10 - 15 minutes between coats



    For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



    Product Notes


    Information On Basic Physical And Chemical Properties
    Polykote 2K TAP Primer
    Form:According to product specification
    Colour:According to product specification
    Odour:Characteristic
    Odour Threshold:Not determined
    pH-value 20°C:Not determined
    Melting point/freezing point:Undetermined
    Initial boiling point and boiling range:124°C
    Flash Point:25°C
    Flammability (solid, gas):Not applicable
    Ignition temperature:370°C
    Decomposition temperature:Not determined.
    Auto-ignition temperature:Product is not selfigniting.
    Explosive properties:"Product is not explosive. However, formation of explosive air vapour mixtures are possible."
    Explosion limits: Lower:1.1 Vol%
    Explosion limits: Upper:7.0 Vol%
    Vapour pressure at 20°C:6.7 hPa
    Density at 20°C:1.097 g/cm³
    Relative density:Not determined
    Vapour density:Not determined
    Evaporation rate:Not determined
    Solubility in / Miscibility with water:NOT MISCIBLE
    Partition coefficient: n-octanol/water:Not determined
    Viscosity: Dynamic at 20°C:350 mPas
    Viscosity: Kinematic:Not determined
    Solvent content: Organic solvents:50.4%
    Solids content:49.6%



    Health & Safety


    • Refer to the safety data sheet in the attachments section above and tin label prior to use.
    • Suitable air fed respiratory equipment should be worn when spraying.

    Click to go back to the top of the page

    Product Details
    4451-690279

    Data sheet

    Manufacturer
    Manufacturer
    Water / Solvent Based
    Solvent
    For Use On
    Metal
    Application Method
    Spray, Pressure pot
    Sheen
    Matt
    Colour
    Clear
    Single, Two or Three Pack
    Three-Pack
    Pack Size
    5L
    Mixing Ratio
    Base: 3 - Hardener: 1 - Thinner: 1
    Suitable Substrates
    OEM finishes
    Suitable Substrates
    OEM finishes when minimum sanding is required
    Touch Dry (at 20°C)
    2 hours
    Dry to Recoat (at 20°C)
    Minimum of 30minutes at 20°C, when used as a Wet on Wet. Minimum of 4 hours at 20°C when flatting.
    Fully Cured (at 20°C)
    8 hours
    Pot Life (at 20°C)
    3 hours
    Coverage
    16.8 square metres per litre @ 25 microns dft mixed
    Recommended Thinner/Cleaner
    Thinner 2601/2602/2603
    Density
    1.097 g/cm³
    Solids by Volume
    49.6 %
    Heat Resistance (up-to)
    120°C
    VOC
    0.600 Kg/l
    Shelf Life (from date of manufacture)
    12 months from delivery date in original sealed containers
    Finish
    Matt
    Size
    5L
    UN Number
    1263
    Base Type
    Solvent-Based
    Suitable For Use On
    Metal
    Finish
    Matt
    Application Method
    Spray
    Product Usage Type
    Primer
    Product Range
    Polykote
    Colour Family
    Clear
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    HMG Polykote 2K TAP Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    HMG Thinner 2601

    HMG Thinner 2601 is a very fast thinner.For use in recommended HMG systems.More Information Delivery Info

    Price £11.22 (ex. VAT)
    In Stock and Available for Delivery

    HMG Thinner 2602

    HMG Thinner 2602 is a medium slow thinner.For use with compatible HMG systems.More Information Delivery Info

    Price £11.26 (ex. VAT)
    In Stock and Available for Delivery

    HMG Thinner 2603

    HMG Thinner 2603 is a medium slow thinner.For use with compatible HMG systems.More Information Delivery Info

    Price £38.22 (ex. VAT)
    In Stock and Available for Delivery

    HMG Hardener 9027 Wintermix

    HMG Hardener 9027 Wintermix is a fast curing, medium solids isocyanate hardener. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) Option 1: HMG Acrythane SC601 ColoursOption 2: HMG Polykote 2K AMC PrimerOption 3: HMG...

    Price £20.42 (ex. VAT)
    In Stock and Available for Delivery

    HMG Hardener 9004 Standard

    HMG Hardener 9004 Standard is a medium solids isocyanate hardener. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) HMG Acrythane SC601 ColoursHMG Acrythane 102HMG 2K Multi Surface TopcoatHMG Polykote 2K AMC Primer...

    Price £24.82 (ex. VAT)
    In Stock and Available for Delivery

    Surface Preparation Kits for Steel

    These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...

    Price £21.53 (ex. VAT)
    In Stock and Available for Delivery