HMG D66 Chassis Black


    HMG D66 Chassis Black is an alkyd based synthetic enamel to suit both brush and spray requirements.

    • Good performance
    • Oil and diesel resistant

    £53.61(ex. VAT)
    £64.33 (inc. VAT)
    Please choose your colour
    Available for Delivery (See Delivery Options Below)


    HMG D66 Chassis Black is an alkyd based synthetic enamel to suit both brush and spray requirements.

    Click To Jump To Section:

    Features & Benefits

    • Good performance
    • Oil and diesel resistant

    Product Specification

    Technical Data
    Volume Solids:50.1%
    VOC Content:0.65kgs/lt
    Viscosity:240 mPas
    Density:0.912 g/cm³
    Storage Conditions:Store between 5°C - 25°C. When not in use, cans must be kept sealed.
    Shelf Life:12 months from delivery date in original sealed containers.
    Flash Point:29°C

    Film Thickness Range And Coverage

    Product Data
     Dry Film ThicknessWet Film Thickness
    Compliant Spray Gun:25 µm50 µm
    HVLP:25 µm50 µm
    Brush:25 µm50 µm
    Roller:25 µm50 µm

    Coverage: 20 square metres per litre @ 25 microns dft

    • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
    • These values are a guide only and are not to be used as specifications.
    • Film thickness will vary depending on actual use and specification.
    • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.

    Drying Times

    Drying Times At 20°C
    Touch Dry:2 - 4 hours
    Dry To Recoat:24 hours minimum
    Fully Cured:24 hours

    Surface Preparation

    • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.

    Application Methods

    Technical Data
    Compliant Spray GunHVLPBrushRoller
    Mixing Ratio:Base: 1Base: 1Ready for useReady for use
    Thinner: approx 10%Thinner: approx 10%--
    Thinner Options:Thinner 2611Thinner 2611--
    Thinner 2612Thinner 2612--
    Number Of Coats (Guide Only):1 dust coat then 1 full coat1 full coat--
    Flash Off:15 minutes15 minutes15 minutes15 minutes

    For futher information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or

    • D66 can be brushed or hot sprayed as supplied.
    • For conventional air assisted spray up to 25% 2611 or 2612 Thinner may be added to suit equipment.

    Product Notes

    Information on basic physical and chemical properties
    Colour:According to product specification.
    Odour Threshold:Not determined
    pH-value:Not determined
    Change in Condition
    Melting point/freezing point:Undetermined
    Initial boiling point and boiling range:135°C
    Flash Point:29°C
    Flammability (solid, gas):Not applicable
    Ignition temperature:200°C
    Decomposition temperature:Not determined.
    Auto-ignition temperature:Product is not selfigniting
    Explosive properties:"Product is not explosive. However, formation of explosive air vapour mixtures are possible."
    Explosion limits: Lower:0.6 Vol %
    Explosion limits: Upper:7.0 Vol %
    Vapour pressure at 20°C:Not determind
    Density at 20°C:0.912 g/cm³
    Relative density:Not determined
    Vapour density:Not determined
    Evaporation rate:Not determined
    Solubility in / Miscibility with water:NOT MISCIBLE
    Partition coefficient: n-octanol/water:Not determined
    Viscosity: Dynamic at 20°C:240 mPas
    Viscosity: Kinematic:Not determined
    Solvent content: Organic solvents:3.8%
    Solids content:50.1%

    Health & Safety

    • Refer to the safety data sheet in the attachments section above and tin label prior to use.
    • Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water and disposed of in a noncombustible container with a tight fitting lid.

    Click to go back to the top of the page

    Product Details

    Data sheet

    HMG Paints Limited
    Water / Solvent Based
    Application Method
    Brush, roller, spray
    Standard / Ready Mixed
    Single, Two or Three Pack
    Single, Two or Three Pack
    Pack Size
    Base Type
    Alkyd based
    Mixing Ratio
    Compliant Spray Gun: Base 1 - Thinner: approx 10%
    Mixing Ratio
    Brush: Base 1 - Thinner: approx 10%
    Key Features
    Oil and diesel resistant
    Touch Dry (at 20°C)
    2 - 4 Hours
    Dry to Recoat (at 20°C)
    24 Hours minimum
    Fully Cured (at 20°C)
    24 Hours
    20 square metres per litre @ 25 microns dft
    0.912 g/cm³
    Solids by Volume
    50.1 %
    Shelf Life (from date of manufacture)
    12 months from delivery date in original sealed containers.
    Recommended Dry Film Thickness
    25 µm
    Recommended Wet Film Thickness
    50 µm
    UN Number
    Base Type
    Base Type
    Suitable For Use On
    Application Method
    Application Method
    Application Method
    Product Type
    Product Range
    Colour Family

    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

    Be the first to ask a question about this product!

    Question about the product

    * Required fields


    HMG D66 Chassis Black is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT

    You might also like

    HMG Thinner 2611

    HMG Thinner 2611 is a medium thinner.For use with compatible HMG systems.More Information Delivery Info

    Price £10.65 (ex. VAT)
    In Stock and Available for Delivery

    HMG Thinner 2612

    HMG Thinner 2612 is a slow thinner.For use with compatible HMG systems.More Information Delivery Info

    Price £10.65 (ex. VAT)
    In Stock and Available for Delivery

    Surface Preparation Kits for Steel

    These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...

    Price £17.22 (ex. VAT)
    In Stock and Available for Delivery