Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life:
12 months from delivery date in original sealed containers.
Flash Point:
31°C
Film Thickness Range And Coverage
Product Data
Dry Film Thickness
Wet Film Thickness
Brush:
50 µm
100 µm
Coverage: 14 square metres per litre @ 50 microns dft.
HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
These values are a guide only and are not to be used as specifications.
Film thickness will vary depending on actual use and specification.
Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.
Drying Times
Drying Times At 20°C
Touch Dry:
4 - 6 hours
Dry To Handle:
12 hours
Dry To Recoat:
After 12 hours
Fully Cured:
24 hours
For professional use only.
This product was designed for brush application onto large areas. It has been developed to provide a long 'wet edge' and an extended drying time. It may not be suitable for small areas or areas that are due to be returned to service in short time-frames. HMG Coach Enamel can be used as a quicker drying alternative.
Surface Preparation
Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
Application Methods
Technical Data
Brush
Mixing Ratio:
Ready for use
-
Thinner Options:
n/a
-
Viscosity:
n/a
Number Of Coats (Guide Only):
n/a
Flash Off:
n/a
Properties can be enhanced by the addition of Hardener 9029. Use 10 parts base to 1 part hardener.
Product Notes
Information on basic physical and chemical properties
Form:
Liquid
Colour:
According to product specification.
Odour:
Characteristic
Odour Threshold:
Not determined
pH-value:
Not determined
Change in Condition
Melting point/freezing point:
Undetermined
Initial boiling point and boiling range:
135°C
Flash Point:
31°C
Flammability (solid, gas):
Not applicable
Ignition temperature:
200°C
Decomposition temperature:
Not determined.
Auto-ignition temperature:
Product is not selfigniting
Explosive properties:
"Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower:
0.6 Vol %
Explosion limits: Upper:
7.0 Vol %
Vapour pressure at 20°C:
2.1 hPa
Density at 20°C:
1.112 g/cm³
Relative density:
Not determined
Vapour density:
Not determined
Evaporation rate:
Not determined
Solubility in / Miscibility with water:
NOT MISCIBLE
Partition coefficient:n-octanol/water:
Not determined
Viscosity: Dynamic at 20°C:
800 mPas
Viscosity: Kinematic:
Not determined
Solvent content: Organic solvents:
27.1%
Solids content:
72.5%
Health & Safety
Refer to the safety data sheet in the attachments section above and tin label prior to use.
Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water and disposed of in a noncombustible container with a tight fitting lid.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Hi, I was wondering if this is suitable as a top coat over a zinc phosphate primer (alkyd). Also what what would be the recommended thinner? Regards, Jason
Answer from Rawlins’ Technical Team:
We would recommend testing for compatibility and adhesion prior to full application with your primer.
The manufacturers recommended primer is HMG Synthetic BDX Primer, this is also an alkyd based primer.
The paint is designed for brush application and is not to be thinned.
HMG SAH300 Enamel is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
HMG Synthetic BDX Primer is a high build, anti-corrosive, single pack alkyd primer for use under all HMG synthetic topcoats, combining high build and excellent sandability with outstanding application and scratch filling properties.
For use on suitably prepared structural steel, chassis, fabrication and aluminium
Can be applied to bare...
HMG Synthetic High Opacity Undercoat is a 1K alkyd/polyurethane undercoat with superior brushing qualities and excellent obliteration properties.
Suitable for large areas due to its ease of application and long wet edge time
Please note: Colours shown are for illustrative purposes only
More Information Delivery Info
HMG Hardener 9029 ZIP is an isocyanate hardener.
Designed for use in recommended HMG Alkyd and Polyurethane Alkyd systems.
Upgrades the performance characterstics of the system, including durability and time to touch dry may decrease by 10 - 20% dependant on paint system, film thickness and curing conditions.
More Information Delivery...
HMG SAH300 Enamel Aerosol is a high solids, gloss 1K polyurethane alkyd aerosol. This product has also been designed to be “Ready for Use”, for the non-aerosol version of this product please see HMG SAH300 Enamel.
400ml/16oz Aerosol
Available in packs of 1 or packs of 6+, 50 and 100 with discounted price breaks
Available in 2,400+...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3).
Please click here for important information about these kits.
Kit Contents:
SET 1 (Hand Tools)
1 x Rust-Oleum...
Jason on 2021-03-21 14:10:03
