HMG Thinner 2641
HMG Thinner 2641 is a medium fast thinner.Designed for use with cellulose based systems.More Information Delivery Info
£14.05 (incl. VAT)
£11.71 (ex. VAT)
We no longer stock this product, but can recommend HMG M99 Cellulose as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
HMG M99 Gipgloss Cellulose Enamel is a high gloss, cellulose finish enabling a first class result to be achieved with minimum cost and labour. Eminently suitable for dual colour work.
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
HMG M99 Gipgloss Cellulose Enamel is a high gloss, cellulose finish enabling a first class result to be achieved with minimum cost and labour. Eminently suitable for dual colour work.
Technical Data | |
---|---|
Volume Solids: | 46.0% |
VOC Content: | 0.61kgs/ltr |
SG: | - |
Viscosity: | 250 mPas |
Density: | 1.08 g/cm³ |
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. |
Shelf Life: | 12 months from delivery date in original sealed containers. |
Flash Point: | -9°C |
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Aerosol: | 25 μm | 50 μm | |
Compliant Spray: | 25 μm | 50 μm |
Coverage: 12.4 square metres per litre @ 25 microns dft (Theoretical)
Drying Times At 20°C | |
---|---|
Touch Dry: | 15 minutes |
Fully Cured: | 5 hours |
Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
Technical Data | |||||
---|---|---|---|---|---|
Aerosol | Compliant Spray Gun | ||||
Mixing Ratio: | Ready for use | Base: 1 | |||
- | Thinner: 1 | ||||
Thinner Options: | - | Thinner 2641 | |||
- | - | ||||
Viscosity: | Ready for use | 25 - 26 seconds B4 cup | |||
Spray Gun Setup: | N/A | 1.4 - 1.8 | |||
Number Of Coats (Guide Only): | 2 - 3 full coats | 2 - 3 full coats | |||
Flash Off: | 10 minutes between coats | 10 minutes between coats |
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Information on basic physical and chemical properties | |
---|---|
Form: | Liquid |
Colour: | According to product specification |
Odour: | Characteristic |
Odour Threshold: | Not determined |
pH-value: | Not determined |
Change in Condition | |
Melting point/freezing point: | Undetermined |
Initial boiling point and boiling range: | 79°C |
Flash Point: | -9°C |
Flammability (solid, gas): | Not applicable |
Ignition temperature: | 287°C |
Decomposition temperature: | Not determined. |
Auto-ignition temperature: | Product is not selfigniting |
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." |
Explosion limits: Lower: | 1.2 Vol % |
Explosion limits: Upper: | 7.1 Vol % |
Vapour pressure at 20°C: | 29 hPa |
Density at 20°C: | 1.08 g/cm³ |
Relative density: | Not determined |
Vapour density: | Not determined |
Evaporation rate: | Not determined |
Solubility in / Miscibility with water: | NOT MISCIBLE |
Partition coefficient: n-octanol/water: | Not determined |
Viscosity: Dynamic at 20°C: | 250 mPas |
Viscosity: Kinematic: | Not determined |
Solvent content: Organic solvents: | 58.3% |
Solids content: | 46.0% |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG M99 Gipgloss Cellulose Enamel is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Thinner 2641 is a medium fast thinner.Designed for use with cellulose based systems.More Information Delivery Info
£14.05 (incl. VAT)
£11.71 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)