HMG Thinner 2424
HMG Thinner 2424 is a thinner recommended for use in certain HMG systems.Designed for use with Acrythane 4G products.More Information Delivery Info
HMG Acrythane 4G Clearcoat (Base) is a high solids acrylic polyurethane coating to meet the stringent requirements of the commercial vehicle market.
This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:
2-Pack System Details | |||||
---|---|---|---|---|---|
Base (Part 1) | HMG Acrythane 4G Clearcoat | ||||
Hardener (Part 2) | HMG Hardener 9047 | ||||
Thinner (Part 3) | HMG Thinner 2424 |
HMG Acrythane 4G Clearcoat is a high solids acrylic polyurethane coating to meet the stringent requirements of the commercial vehicle market.
Please note this product is one part of a three-pack system which MUST be purchased/used together with HMG Hardener 9047 and HMG Thinner 2424.
Technical Data | ||||||
---|---|---|---|---|---|---|
HMG Acrythane 4G Clearcoat | ||||||
Volume Solids: | 59.2% | |||||
VOC Content: | 0.420kgs/ltr | |||||
SG: | - | |||||
Viscosity: | 270 mPas | |||||
Density: | 1.018 g/cm³ | |||||
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | |||||
Shelf Life: | 12 months from delivery date in original sealed containers. | |||||
Pot Life: | Maximum 5 seconds increase after 30 min. | |||||
Flash Point: | 25°C |
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Gravity Gun: | 50 μm | 110 μm | |
Suction Feed: | 50 μm | 110 μm | |
Pressure Pot: | 50 μm | 110 μm |
Coverage: 12 - 14 square metres per litre @ 80 microns wft (Theoretical)
Drying Times At 20°C | |
---|---|
Touch Dry: | 30 minutes |
Dry To Handle: | 1 hour |
Dry To Recoat: | After hard dry (8 hours @ 20°C) denib with p500g dry. After baking allow to cool before flatting and recoating. |
Fully Cured: | 8 hours |
Technical Data | |||||
---|---|---|---|---|---|
Gravity Gun | Suction Feed | Pressure Pot | |||
Mixing Ratio: | Base: 3 | Base: 3 | Base: 3 | ||
Hardener: 1 | Hardener: 1 | Hardener: 1 | |||
Thinner: 1 | Thinner: 1 | Thinner: 1 | |||
Hardener Options: | Hardener 9047 Standard | Hardener 9047 Standard | Hardener 9047 Standard | ||
Thinner Options: | Thinner 2424 | Thinner 2424 | Thinner 2424 | ||
Viscosity: | 28 - 32 seconds B4 cup | 28 - 32 seconds B4 cup | 28 - 32 seconds B4 cup | ||
Spray Gun Setup: | 1.3 - 1.5 | 1.6 - 1.8 | 0.85 - 1.2 | ||
Number Of Coats (Guide Only): | 2 | 2 | 2 | ||
Flash Off: | Minimum 10 minutes | Minimum 10 minutes | Minimum 10 minutes |
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Information On Basic Physical And Chemical Properties | ||||||
---|---|---|---|---|---|---|
HMG Acrythane 4G Clearcoat | ||||||
Form: | According to product specification | |||||
Colour: | According to product specification | |||||
Odour: | Characteristic | |||||
Odour Threshold: | Not determined | |||||
pH-value 20°C: | Not determined | |||||
Melting point/freezing point: | Undetermined | |||||
Initial boiling point and boiling range: | 100°C | |||||
Flash Point: | 25°C | |||||
Flammability (solid, gas): | Not applicable | |||||
Ignition temperature: | 415°C | |||||
Decomposition temperature: | Not determined. | |||||
Auto-ignition temperature: | Product is not selfigniting. | |||||
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | |||||
Explosion limits: Lower: | 1.2 Vol % | |||||
Explosion limits: Upper: | 7.5 Vol % | |||||
Vapour pressure at 20°C: | 11.2 hPa | |||||
Density at 20°C: | 1.018 g/cm³ | |||||
Relative density: | Not determined | |||||
Vapour density: | Not determined | |||||
Evaporation rate: | Not determined | |||||
Solubility in / Miscibility with water: | NOT MISCIBLE | |||||
Partition coefficient: n-octanol/water: | Not determined | |||||
Viscosity: Dynamic at 20°C: | 270 mPas | |||||
Viscosity: Kinematic: | Not determined | |||||
Solvent content: Organic solvents: | 40.5% | |||||
Solids content: | 59.2% |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG Acrythane 4G Clearcoat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Thinner 2424 is a thinner recommended for use in certain HMG systems.Designed for use with Acrythane 4G products.More Information Delivery Info
HMG Hardener 9047 is a hardener for use with recommeded HMG systems. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) HMG Acrythane 4G ClearcoatHMG Acrythane 4G ColoursHardener (Part 2) HMG Hardener 9047...
£144.96 (incl. VAT)
£120.80 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)