HMG Cellulose APS Primer

    PRIE9
    HMG4429

    HMG Cellulose APS Primer is a quick drying cellulose primer for use in aerosols, classic car refinish and industrial applications.

    Colour
    Size
    Finish
    £20.87(ex. VAT)
    £25.04 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    HMG Synthetic LP Primer is a quick drying cellulose primer for use in aerosols, classic car refinish and industrial applications.



    • Not to be used in connection with 2004/42/CE.



    Click To Jump To Section:




    Features & Benefits


    • Available in grey or white



    Product Specification


    Technical Data
    Cellulose APS1 PrimerCellulose APS2 White Primer Filler
    Volume Solids:41.5%54.0%
    VOC Content:0.670Kg/L0.670Kg/L
    SG:--
    Viscosity:Not determined200 mPas
    Density:1.202 g/cm³1.205 g/cm³
    Storage Conditions:Store between 5°C - 25°C. When not in use, cans must be kept sealed.Store between 5°C - 25°C. When not in use, cans must be kept sealed.
    Shelf Life:12 months from delivery date in original sealed containers.12 months from delivery date in original sealed containers.
    Pot Life:--
    Flash Point:4°C4°C



    Film Thickness Range And Coverage


    Product Data
     Dry Film ThicknessWet Film Thickness
    Compliant Spray Gun:30 - 50 μm60 - 100 μm



    Coverage: 20 square metres per litre @ 20 microns dft (Theoretical)

    • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
    • These values are a guide only and are not to be used as specifications.
    • Film thickness will vary depending on actual use and specification.
    • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



    Drying Times


    Drying Times At 20°C
    Touch Dry:10 minutes
    Dry To Recoat:After 30 minutes
    Fully Cured:30 minutes



    Surface Preparation


    • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
    • Read and follow the Safety Data Sheet, Product Data Sheet and label instructions.
    • Stir all paints thoroughly before use.
    • Always use the same batch number on the same job.
    • Check colour & sheen.
    • Filter the product immediately before use.
    • Reduce emissions and maintain quality by replacing tin lid after use.



    Application Methods


    Technical Data
    Compliant Spray Gun
    Mixing Ratio:Base: 1
    Thinner: 1
    Thinner Options:Thinner 2641
    Thinner 2642
    Viscosity:28 - 35 seconds B4 cup
    Spray Gun Setup:-
    Number Of Coats (Guide Only):2 - 3 coats
    Flash Off:5 minutes between coats



    For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



    Product Notes


    Information On Basic Physical And Chemical Properties
    Cellulose APS1 PrimerCellulose APS2 White Primer Filler
    Form:According to product specificationAccording to product specification
    Colour:According to product specificationAccording to product specification
    Odour:CharacteristicCharacteristic
    Odour Threshold:Not determined
    pH-value 20°C:Not determinedNot determined
    Melting point/freezing point:UndeterminedUndetermined
    Initial boiling point and boiling range:78°C82°C
    Flash Point:4°C4°C
    Flammability (solid, gas):Not applicableNot applicable
    Ignition temperature:370°C370°C
    Decomposition temperature:Not determined.Not determined.
    Auto-ignition temperature:Product is not selfigniting.Product is not selfigniting.
    Explosive properties:"Product is not explosive. However, formation of explosive air vapour mixtures are possible.""Product is not explosive. However, formation of explosive air vapour mixtures are possible."
    Explosion limits: Lower:1.2 Vol %1.1 Vol %
    Explosion limits: Upper:7.0 Vol %7.0 Vol %
    Vapour pressure at 20°C:29 hPa6.7 hPa
    Density at 20°C:1.202 g/cm³1.205 g/cm³
    Relative density:Not determinedNot determined
    Vapour density:Not determinedNot determined
    Evaporation rate:Not determinedNot determined
    Solubility in / Miscibility with water:NOT MISCIBLENOT MISCIBLE
    Partition coefficient: n-octanol/water:Not determinedNot determined
    Viscosity: Dynamic at 20°C:Not determined200 mPas
    Viscosity: Kinematic:Not determinedNot determined
    Solvent content: Organic solvents:47.2%46.9%
    Solids content:41.5%54.0%



    Health & Safety


    • Refer to the safety data sheet in the attachments section above and tin label prior to use.
    • Suitable respiratory equipment should be worn when spraying.

    Click to go back to the top of the page

    Product Details
    4429-685823

    Data sheet

    Manufacturer
    HMG Paints Limited
    Water / Solvent Based
    Solvent
    For Use On
    Metal
    Application Method
    Spray
    Sheen
    Matt
    Colour
    Standard / Ready Mixed
    Single, Two or Three Pack
    Single
    Pack Size
    1L, 5L
    Mixing Ratio
    Base: 1 - Thinner: 1
    Touch Dry (at 20°C)
    10 Mins
    Dry to Recoat (at 20°C)
    After 30 mins
    Fully Cured (at 20°C)
    30 Mins
    Coverage
    20 square metres per litre @ 20 microns dft
    Recommended Thinner/Cleaner
    Thinner 2641 - Thinner 2642
    Density
    Cellulose APS1 Primer: 1.202 g/cm³ - Cellulose APS2 White Primer Filler: 1.205 g/cm³
    Solids by Volume
    Cellulose APS1 Primer: 41.5 % - Cellulose APS2 White Primer Filler: 54.0 %
    Heat Resistance (up-to)
    80°C
    VOC
    0.670kgs/ltr
    Recommended Dry Film Thickness
    30 - 50 μm
    Recommended Wet Film Thickness
    60 - 100 μm
    UN Number
    UN1263
    Base Type
    Solvent-Based
    Suitable For Use On
    Metal
    Finish
    Matt
    Application Method
    Spray
    Product Usage Type
    Primer
    Product Range
    Cellulose
    Colour Family
    Grey
    Colour Family
    White
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    HMG Cellulose APS Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    HMG Thinner 2641

    HMG Thinner 2641 is a medium fast thinner.Designed for use with cellulose based systems.More Information Delivery Info

    Price £10.65 (ex. VAT)
    In Stock and Available for Delivery

    HMG Thinner 2642

    HMG Thinner 2642 is a medium slow thinner which can be used with compatible HMG systems.For use with cellulose based systems.More Information Delivery Info

    Price £36.01 (ex. VAT)
    In Stock and Available for Delivery

    HMG Cellulose APS Primer Aerosol

    HMG Cellulose APS Primer Aerosol is a quick drying cellulose primer for use in aerosols, classic car refinish and industrial applications. This product is also available in non-aerosol form, please see HMG Cellulose APS Primer.400ml/16oz Aerosol Matt finish Available in grey (APS2) or white (APS1) Please note: Not to be used in...

    Price £12.46 (ex. VAT)
    In Stock and Available for Delivery

    Surface Preparation Kits for Steel

    These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...

    Price £21.53 (ex. VAT)
    In Stock and Available for Delivery