HMG Thinner 2601
HMG Thinner 2601 is a very fast thinner.For use in recommended HMG systems.More Information Delivery Info
HMG Polykote 2K TAP Primer (Base) is a transparent 2K adhesion promoter /primer / sealer. It is designed for use on sound OEM finishes when minimum sanding is required and has the additional benefit of being used as a `wet on wet` primer to optimise process times.
This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener/thinner:
3-Pack System Details | |||||
---|---|---|---|---|---|
Base (Part 1) | HMG Polykote 2K TAP Primer | ||||
Hardener (Part 2) | HMG Hardener 9004 Standard | ||||
HMG Hardener 9027 Wintermix | |||||
Thinner (Part 3) | HMG Thinner 2601 | ||||
HMG Thinner 2602 | |||||
HMG Thinner 2603 |
HMG Polykote 2K TAP Primer is a transparent 2K adhesion promoter/primer/sealer. It is designed for use on sound OEM finishes when minimum sanding is required and has the additional benefit of being used as a 'wet on wet' primer to optimise process times.
Please note this product is one part of a three-pack system which MUST be purchased/used together with HMG Hardener 9004 Standard or HMG Hardener 9027 Wintermix. A thinner option must also be purchased from HMG Thinner 2601, HMG Thinner 2602 or HMG Thinner 2603.
It is particularly suitable for colour changes to new vehicles as no sanding is required, however it is recommended that leading edges, such as wheelarches, front of bonnets etc, are scotchbrited for maximum performance.
Not for use as a bare metal primer.
Technical Data | ||||||
---|---|---|---|---|---|---|
Polykote 2K TAP Primer | ||||||
Volume Solids: | 49.6% | |||||
VOC Content: | 0.600 Kg/l | |||||
SG: | - | |||||
Viscosity: | 350 mPas | |||||
Density: | 1.097 g/cm³ | |||||
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | |||||
Shelf Life: | 12 months from delivery date in original sealed containers. | |||||
Pot Life: | 3 hours at 20°C | |||||
Flash Point: | 25°C |
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Compliant Spray Gun: | 25 μm | 50 μm | |
Pressure Pot: | 25 μm | 50 μm |
Coverage: 16.8 square metres per litre @ 25 microns dft mixed
Drying Times At 20°C | |
---|---|
Touch Dry: | 2 hours |
Dry To Recoat: | Minimum of 30 minutes at 20°C, when used as a Wet on Wet. Minimum of 4 hours at 20°C when flatting. |
Fully Cured: | 8 hours |
Technical Data | |||||
---|---|---|---|---|---|
Compliant Spray Gun | Pressure Pot | ||||
Mixing Ratio: | Base: 3 | Base: 3 | |||
Hardener: 1 | Hardener: 1 | ||||
Thinner: 1 | Thinner: 1 | ||||
Hardener Options: | Hardener 9004 Standard | Hardener 9004 Standard | |||
Hardener 9027 Wintermix | Hardener 9027 Wintermix | ||||
Thinner Options: | Thinner 2601 | Thinner 2601 | |||
Thinner 2602 | Thinner 2602 | ||||
Thinner 2603 | Thinner 2603 | ||||
Viscosity: | 16 - 22 seconds B4 cup | 16 - 22 seconds B4 cup | |||
Spray Gun Setup: | 1.6 - 1.8 | 1.1 - 1.4 | |||
Number Of Coats (Guide Only): | 1 - 2 even coats | 1 - 2 even coats | |||
Flash Off: | 10 - 15 minutes between coats | 10 - 15 minutes between coats |
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Information On Basic Physical And Chemical Properties | ||||||
---|---|---|---|---|---|---|
Polykote 2K TAP Primer | ||||||
Form: | According to product specification | |||||
Colour: | According to product specification | |||||
Odour: | Characteristic | |||||
Odour Threshold: | Not determined | |||||
pH-value 20°C: | Not determined | |||||
Melting point/freezing point: | Undetermined | |||||
Initial boiling point and boiling range: | 124°C | |||||
Flash Point: | 25°C | |||||
Flammability (solid, gas): | Not applicable | |||||
Ignition temperature: | 370°C | |||||
Decomposition temperature: | Not determined. | |||||
Auto-ignition temperature: | Product is not selfigniting. | |||||
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | |||||
Explosion limits: Lower: | 1.1 Vol% | |||||
Explosion limits: Upper: | 7.0 Vol% | |||||
Vapour pressure at 20°C: | 6.7 hPa | |||||
Density at 20°C: | 1.097 g/cm³ | |||||
Relative density: | Not determined | |||||
Vapour density: | Not determined | |||||
Evaporation rate: | Not determined | |||||
Solubility in / Miscibility with water: | NOT MISCIBLE | |||||
Partition coefficient: n-octanol/water: | Not determined | |||||
Viscosity: Dynamic at 20°C: | 350 mPas | |||||
Viscosity: Kinematic: | Not determined | |||||
Solvent content: Organic solvents: | 50.4% | |||||
Solids content: | 49.6% |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG Polykote 2K TAP Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Thinner 2601 is a very fast thinner.For use in recommended HMG systems.More Information Delivery Info
HMG Thinner 2602 is a medium slow thinner.For use with compatible HMG systems.More Information Delivery Info
HMG Thinner 2603 is a medium slow thinner.For use with compatible HMG systems.More Information Delivery Info
HMG Hardener 9027 Wintermix is a fast curing, medium solids isocyanate hardener. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) Option 1: HMG Acrythane SC601 ColoursOption 2: HMG Polykote 2K AMC PrimerOption 3: HMG...
HMG Hardener 9004 Standard is a medium solids isocyanate hardener. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) HMG Acrythane SC601 ColoursHMG Acrythane 102HMG 2K Multi Surface TopcoatHMG Polykote 2K AMC Primer...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...